Service HotlineWith the advancement of technology in various industries, the current structural design of screws has evolved from just simple locking to focusing on work efficiency during the locking process and not destroying the integrity of the objects to be locked. The new cases such as No. 556784 screw improvement and No. 289405 screw that integrates locking, stability, labor-saving, fast and multi-function which were previously designed and approved and published in the Central Taiwan Bulletin are the main representatives of screws. It is clear that It is learned that the two cases not only fully improve the shortcomings of the traditional simple locking screws, but also achieve the purpose of substantial improvement of the screws designed in each case in actual use.
As my digital TV technology becomes more and more mature, more and more people with digital-to-analog signal conversion function enter people's lives. Therefore, the number of production and processing is also increasing day by day. There are many requirements for the form, reliability and cost of PCB fixing screws in production. One of the existing fixing methods is to fix by means of bolts and nuts. The operation steps are to place the PCB board on the inner threaded copper column connected to the casing, and pass through the bolts with fine teeth. Screw holes on the PCB board, and then fix them on the copper posts with nuts. The connection method of this solution is reliable, but its manufacturing cost is high, and the copper column and the metal shell need to be screwed together, resulting in low production efficiency and high cost. In addition, there is also a common way that the PCB is supported by a plastic column, and the self-tapping screw is passed through the screw hole on the PCB board, and the PCB board and the metal bottom shell are connected by the self-tapping thread on the screw. The main disadvantage of this solution is that after the screw is fixed on the metal shell, the screw head is exposed at the bottom of the machine. If the user is not careful during use, the hand scratching phenomenon will occur, which will bring changes and harm to the user's use. . And when the machine slides on the desktop, if the screw head is too exposed, it will scratch the desktop. Therefore, how to provide a PCB fixing method with convenient operation, reliable connection and low production cost is a technical problem to be solved urgently in the industry.
Supporting T-bolts for pre-embedded channels, including hot-rolled pre-embedded channels, the lower part of the pre-embedded channel is provided with a longitudinal opening, and the head of the T-bolt enters from the opening and is clamped in the pre-embedded channel. There are plane teeth at the connection between the buried channel and the T-bolt, and the T-bolt has a tooth-shaped structure matched with the plane teeth. The direction of the teeth is parallel to the slotting direction, and the tooth-shaped cooperation achieves anti-slip effect. However, when the nut tightened on the T-bolt becomes loose, it will cause the T-bolt to move into the embedded channel and lose the toothed fit, thus changing the fixed position of the T-bolt in the embedded channel.
Currently, the method of fixing objects on cement is with cement nails or expansion screws. Cement nails are objects made of hard alloy steel that look like iron nails, which are composed of nail tips and nail bodies. Cement nails are hammered into the cement. Cement nails are easy to drive in, but not removable. The expansion screw is composed of a large end screw, a slotted sleeve, a gasket, a spring washer, and a nut. When using, first drill a hole in the cement with an electric hammer, put in the expansion screw, and tighten the nut to make the slotted sleeve expand at the tail of the big tail screw, so as to fix the expansion screw on the cement. At this time, unscrew the nut to install a fixed object on the expansion screw. Although this method can be disassembled, an electric hammer is required for the first installation, which is inconvenient.
The main purpose of the screw is to make the industrial product form a fixed one. In use, it often happens that the teeth cannot be closely attached, the screw head will be broken if the screw is locked too hard, or the tooth pattern is not properly locked, etc., and the use conditions are not met, all of which are quality. the problem of accuracy. Screws are mass products, not handmade works of art. In mass production, the purpose is to achieve high-precision and stable quality and popular prices to supply consumers. The accuracy of screws is usually 6g, and the rough screws used in construction projects are 14g. The value of screws is very important. In the world, there are examples of automobile factories going bankrupt because of poor screw quality; there are also examples of planes falling and vehicles being overturned because of poor screw quality.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: SO3.5 through-hole pressure riveting standoffs, claw bolts, white zinc screws, outer and inner serrated stop washers and other products, we can provide You have the right fastener solution for you.
