Service HotlineThe embedded nut proposed by Guangdong Yueluo Hardware Industry Co., Ltd. is used to be embedded in an injection molded part. The embedded nut is arranged in a column shape and has a screw hole inside. The embedded nut includes an outer peripheral surface and is formed in the inner nut. The upper end surface and the lower end surface of the two ends of the embedded nut are provided with knurling on the outer peripheral surface, and a guide surface is formed at the connection between the outer peripheral surface and the lower end surface.
1. Material strain hardening When the material is cyclically loaded, the phenomenon of cyclic strain hardening or cyclic strain softening will occur, that is, under the condition of constant cyclic strain, the stress amplitude will increase or decrease with the increase of the number of cycles. . After several cycles, the stress amplitude enters a cyclic steady state. The low-cycle fatigue of the lock nut is carried out under the condition that the strain is constant, and the strain hardening or softening of the threaded piece will affect the size of its maximum unscrewing torque. The alloy steel used to make the lock nut is a cyclic strain hardening material, and the hardening of the material will increase the elastic restoring force FN of the threaded sheet and increase the unscrewing torque.
Make further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 449N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
The technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is: Guangdong Yueluo Hardware Industry Co., Ltd. discloses an anti-dropping nut, which includes a lock, a lock plate, a nut body, a lock ring and a lock claw. The lock ring and the nut body When used together, the lock ring is a circular ring, the inner diameter of the lock ring is larger than the inner diameter of the circumscribed circle of the nut body, the outer diameter of the lock ring is smaller than the inner diameter of the lock buckle, the lock disk is an arc-shaped metal plate, and the number of lock disks is greater than or equal to three. One short side end of the lock plate is connected to the nut body, and the other end of the lock plate is connected to the lock pawl, the lock plate is inclined to the outside of the nut body, and the lock catch is arranged on the outer side of the connection end between the lock pawl and the lock plate. On the side, the lock is a concave arc.
In the process of our transformation and upgrading from big manufacturing to strong manufacturing, the talents of the main body of innovation play an important catalytic role, including a large number of engineers, and drawings are a necessary expression tool for their practical innovation. Engineering drawing courses, as the basic courses of engineering colleges, play an important role in students' ability to read and output engineering drawings, and are directly related to the innovation ability in future work practice.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB889.2 nuts, 304 non-standard screws, heptagon head handle screws, cover type decorative nuts and other products, we can provide you with suitable products for you. Fastener Solutions.
