Service HotlineThe isolating switch in the substation has a large workload for maintenance. The transmission parts such as the isolating switch connecting rod are mostly connected by cylindrical pins. The shaft-pin fit is generally 1mm, which is tight. If the cylindrical pin is disassembled during the maintenance process, it is often due to corrosion and mechanical deformation. It is difficult to proceed smoothly for other reasons, and if the working environment is a small space, it is more difficult to disassemble. In traditional operations, grinding, hard prying, or beating with a hand hammer are often used to disassemble, which will further deform the pins, and when the space is small, it is difficult to use tools such as hand hammers. solve.
At present, shaft retaining rings are mainly divided into three categories: elastic retaining rings for shafts, flattened wire retaining rings for shafts, and wire retaining rings for shafts. Among them, the spring retaining ring for the shaft is generally installed with circlip pliers, and the flattening wire retaining ring for the shaft and the wire retaining ring for the shaft are generally installed with a sharp screwdriver or needle-nose pliers. The defects and deficiencies of these two methods will be discussed in detail below: First, the above two installation methods require the operator to use a large force to open the retaining ring, which is more laborious; For the installation of the flattened steel wire retaining ring for the shaft and the steel wire retaining ring for the shaft, because the wire retaining ring has low elasticity and has no force point, it is very easy to cause the retaining ring to break or the installation tool to slip during the installation process. Higher skills and experience can be competent for the installation of wire retaining rings.
nut is a connecting nut, a part that is screwed together with a bolt or connecting screw for fastening, and a component that must be used in all production and manufacturing machinery. There are many kinds of nuts, we commonly have standard, German standard, British standard, American standard, Japanese standard nuts. According to different materials, nuts are divided into carbon steel, high strength, stainless steel, plastic steel and other types. According to the product attributes, the corresponding standard numbers are divided into ordinary, non-standard, standard, new standard, American system, British system, and German standard. Different sizes, unequal threads are divided into different specifications. The general standard and German standard are represented by M, and the American system and the British system are represented by fractions or #. The specification nut is a part that tightly connects the mechanical equipment. Only through the inner thread, the same specification nut and screw can be connected together. The anti-loosening of the screw has always been the intersection of people's attention. The anti-loosening of the nut is of great significance to the current life, because it directly affects the service life of the machine. Therefore, it is also very important for people's life safety. Technicians can achieve the anti-feeding of the nut by changing the material of the nut and increasing the method of tightening the nut, but these methods cannot fundamentally solve the problem, and increase the tightening nut while taking up more space.
Compared with the prior art, the beneficial effects of Guangdong Yueluo Hardware Industry Co., Ltd. are as follows: the square nut has a simple structure, strong practicability and good fastening effect, which changes the smooth plane design of the traditional square nut. There are circular protrusions, and strip protrusions and strip grooves are respectively provided at the two circular protrusions to increase the roughness of the contact surface of the nut, thereby effectively increasing the friction between the nut body and the fastener. , to achieve a good tightening effect.
Many parts on the car need to be rubberized, which can reduce noise, especially the parts related to shock absorption. Nuts are welded on many of these parts to facilitate the installation of other parts on them. The sheet metal is generally relatively thin, and most of them are only one or two millimeters. A through hole is punched, and then the nut is placed in the hole, and then around it. Spot welding is done so that it can be fixed. After spot welding, the periphery of the screw hole on the sheet metal will not be flat due to thermal deformation, which will affect the appearance.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: external hexagon flange bolts, stud screws, ultra-thin flat washers, plywood nuts and other products, we can provide you with suitable fasteners. Firmware Solutions.
