The research on rivet nuts started in the 1970s in my country and is still in the design and development stage. In the mid-1980s, equipment for the production of blind rivets was introduced from abroad, but no rivet nut has been produced so far. After the inventor's search, no low-carbon steel rivet nut was found to be publicly used.
Anti-corrosion technology Stainless steel screws are made of metal, and there are four main methods for metal anti-corrosion, namely the properties of the material itself, the environment of use, the interface between materials and the environment, and the improvement of the metal structure design. If a complete anti-corrosion alloy is used to make stainless steel Screws, unless there is a special need, are not cost-effective in terms of economics, and it is also impractical to completely isolate the appearance of the screw from environmental elements that can cause corrosion. Improving the metal structure design can improve the influence of special circumstances under certain conditions, but the design of most stainless steel screws cannot be fully corrected, and its maintenance effect is not permanent, so this method cannot basically solve the problem, as long as it is on the surface. Top anti-corrosion, that is, surface anti-corrosion treatment is the most widely used method. The anti-corrosion treatment on the surface of stainless steel screws refers to the use of various methods to apply a protective layer on the metal surface. The purpose of avoiding or mitigating corrosion. The protection layer should be able to meet the following requirements: 1. Corrosion resistance, wear resistance, high hardness, 2. The structure is tight, intact, and the pores are small. 3. It has strong separation and good adhesion with the base metal. 4. It is evenly distributed and has a certain thickness. The maintenance layer is usually divided into two types: metal coating and non-metallic coating. Metal coating refers to the use of metal or alloy with strong corrosion resistance to form a maintenance layer on the surface of metal that is easy to corrode. This coating is also called plating. There are quite a few methods and varieties to produce metal coatings, the most common of which is electroplating, followed by molten metal immersion plating (hot dipping) and chemical surface treatment. Non-metallic coating refers to the use of organic polymer materials such as paint and inorganic materials such as ceramics to form a protective layer on the surface of metal equipment or parts. The protective layer can completely isolate the base metal from the environmental medium and prevent the base metal from corrosion due to contact. Corrosion is formed in the medium of stainless steel standard parts.
flange T-bolt, comprising: a T-bolt including a threaded tooth body and a bolt head fixedly connected to the threaded tooth body; a flange gasket with a plurality of clip teeth, the flange gasket passing through the The plurality of clamping teeth are clamped with the bolt head of the T-bolt. The technical solution of the utility model is that when the groove-type embedded parts are embedded vertically or at a certain angle, the plastic flange of the new T-bolt will help the bolt to be pre-positioned at a certain position of the groove. When multiple T-bolts are used for fixing, Only one worker needs to pre-arrange the bolt positions and then lock the nuts, which greatly improves the construction efficiency.
Yueluo's thin plate rivet method, the thickness of the metal thin plate is less than 0.8mm. The convex rib extrudes the metal sheet adjacent to the rivet hole. The protruding rib is annular, and the protruding rib surrounds the rivet. The rivet head is provided with a positioning structure, the rivet head is provided with a positioning structure for docking the positioning structure, and the positioning structure and the positioning structure are mutually butted through the rivet to align the convex rib with the rivet
In order to effectively improve the working efficiency of bearing installation when the equipment or device is being installed with flat pads, it is necessary to arrange the positions of the front and back of the flat pad.エ Time-consuming, labor-intensive, low production efficiency, high processing cost defects, at the same time, there is a shortage of unstable product quality, so the development of a flat pad front identification feeding mechanism has become a hot spot of industry research.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: self-tapping expansion screws, processing screws, nylon cross head bolts, A-grade carbon steel stud bolts and other products, we can provide you with suitable products Your fastener solution.