Service HotlineAnchor bolts can be divided into fixed anchor bolts, movable anchor bolts, expansion anchor anchor bolts and adhesive anchor bolts. According to the different shapes, it is divided into: L-shaped embedded bolts, 9-shaped embedded bolts, U-shaped embedded bolts, welded embedded bolts, and bottom plate embedded bolts.
The process of removing iron oxide plate from cold heading steel wire rod is stripping and dephosphorization. There are two methods: mechanical dephosphorization and chemical pickling. Replacing the chemical pickling process of wire rod with mechanical phosphorus removal not only improves productivity, but also reduces environmental pollution. This phosphorus removal process includes bending method (the round wheel with triangular grooves is commonly used to repeatedly bend the wire rod), spray nine method, etc. The phosphorus removal effect is good, but the residual iron and phosphorus cannot be removed (the removal rate of iron oxide scale is 97%) ), especially when the iron oxide scale is very sticky, therefore, mechanical phosphorus removal is affected by iron scale thickness, structure and stress state. Carbon steel wire rods used for low strength fasteners (less than or equal to 6.8) High-strength bolts (greater than or equal to grade 8.8) use wire rods to remove all iron oxide scales after mechanical dephosphorization, and then go through a chemical pickling process for compound dephosphorization. For low carbon steel wire rods, the iron sheets left by mechanical dephosphorization are likely to cause uneven wear of grain draft. When the grain draft hole adheres to the iron sheet when the wire rod rubs against the external temperature, the surface of the wire rod produces longitudinal grain marks. More than 95% are caused by scratches on the surface of the steel wire during the drawing process. Therefore, the mechanical phosphorus removal method is not suitable for high-speed drawing.
1. No matter what industry it is, the business is more difficult, and it is still more difficult for the fastener business. After a long period of contact, I realized that the business of making fasteners also requires a lot of attention to be able to do it well. In the business of making fasteners, not just any person can do it, and they all have certain requirements. 2. When it comes to the business of fasteners, no matter what kind of salesperson, the first thing you must have is enough patience, so that we can do this job with confidence, and some customers are not difficult to follow us. Communication, as long as we have enough patience, then we have a greater chance of being able to cooperate with customers on fasteners, and in the face of some relatively large fastener customers, sometimes it is not that we can get it all at once , Sometimes if you want to cooperate, you need to go through multiple contacts to promote a cooperation, so as a salesperson, enough patience is essential. 3. Then, as a fastener salesman, what you need to have is perseverance. Sometimes the salesperson is difficult at work. At this time, you need to adjust it in time, so it will not lead to the phenomenon of giving up easily, after all As a salesman, only through our own efforts can we have the opportunity to receive orders for fasteners from customers. What we need is to be able to face difficulties and move forward bravely. 4. The most important thing for fastener salesmen is to pay attention to details. If we can do a good job in the details, then sometimes we are not far from success. The above are several requirements that need to be met in the fastener business.
Heat treatment technology has a crucial impact on high-strength fasteners, especially its intrinsic quality. Therefore, in order to produce high-quality high-strength fasteners, advanced heat treatment technology and equipment must be available. 1. Status of heat treatment of high-strength fasteners High-strength fasteners have 4 performance levels, namely 8.8, 9.8, 10.9, and 12.9. These four grades of high-strength fasteners must be quenched and tempered. The purpose of heat treatment and tempering is to improve the comprehensive mechanical properties of fasteners to meet the specified tensile strength value and yield ratio of the product. Therefore, the quenching and tempering process has strict requirements on raw materials, furnace temperature control, furnace atmosphere control, quenching medium, heat treatment quality inspection and control, etc.
GB6177 Hexagon Flange Nuts - Grade GB55 Hexagon Thick Nuts GB56 Hexagon Extra Thick Nuts GB1229 Large Hexagon Nuts (High Strength for Steel Structure) Lock Nuts Other Names: Root Nuts, Lock Nuts, and Nuts. Purpose: To lock the outer joint of the through wire or other pipe fittings. The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: water heater expansion screws, SUS316 screws, color zinc lock nuts, national standard 8.8 screws and other products, we can provide you with suitable fasteners for you solution.
