Service HotlineGuangdong Yueluo Hardware Industry Co., Ltd. discloses a telescopic screw. The main point of its technical solution is that it includes an upper screw rod, one end of the upper screw rod is provided with a screw head, and the other side of the upper screw rod opposite to the screw head is provided with a lower screw rod, and the lower screw rod is provided on the other side. A fixing rod is provided, a limiting hole is set on the fixing rod, a sliding rod is set on the upper screw rod, a limiting block matching the limiting hole is set on the sliding rod, and a cover plate is slidably sleeved on the sliding rod. An inner thread is arranged on the plate, a thread matching the inner thread is arranged on the fixing rod, an elastic member is sleeved on the fixing rod, and both ends of the elastic member are respectively in conflict with the upper screw rod and the lower screw rod. Guangdong Yueluo Hardware Industry Co., Ltd. telescopic screw is provided with a telescopic mechanism between the upper screw and the lower screw. Therefore, the screw can be suitable for threaded installation holes with the same diameter and different lengths, avoiding the screw being limited by the length of the threaded hole and unable to be installed.
Inspection method There are two types of screw surface inspection, one is the inspection before the screw is produced and not plated, and the other is the inspection after the screw is plated, that is to say, after the screw is hardened and the surface of the screw is treated. . After the screws are produced and before electroplating, we inspect the screws in various aspects such as size and tolerance. See if there are national standards or customer requirements. After the surface treatment of the screws, we will inspect the plated screws, mainly to check the color of the plating and whether there are any broken screws. In this way, when we deliver screw goods to customers, customers can successfully pass the customs when they receive the goods. Inspection of screws after treatment: 1. Appearance quality requirements The inspection of the appearance of screws is carried out from the aspects of appearance, electroplating layer and so on. Second, the inspection of the thickness of the screw coating 1. The measuring tool method uses a micrometer, a vernier caliper, a plug gauge, etc. 2. Magnetic method The magnetic method is used to measure the thickness of the coating layer, which is a non-destructive measurement of the non-magnetic coating layer on the magnetic substrate with a magnetic thickness gauge. 3. Microscopy Microscopy is called metallographic method, which is to magnify the etched fasteners on a metallographic microscope with a micrometer eyepiece to measure the thickness of the coating on the section. 4. Timing flow method The timing flow method uses a solution that can dissolve the coating to flow on the local surface of the coating, and calculates the thickness of the coating according to the time required for the local coating to dissolve. There are also coating drop method, anodic dissolution Coulomb method, etc. 3. Inspection of the adhesion strength of the screw coating There are many methods for evaluating the adhesion between the coating and the base metal, usually the following. 1. Friction polishing test; 2. File method test; 3. Scratch method; 4. Bending test; 5. Thermal shock test; 6. Extrusion method. 4. Inspection of corrosion resistance of screw coatings The corrosion resistance inspection methods of coatings include: atmospheric exposure test; neutral salt spray test (NSS test); acetate salt spray test (ASS test), copper accelerated acetate salt spray test (CASS) test); and corrosion paste corrosion test (CORR test) and solution spot corrosion test; immersion test, inter-dipping corrosion test, etc.
At present, the screws used by people are not provided with a device that does not loosen, especially in some key parts, if the screws are loosened, it will cause heavy losses. In order to overcome the current situation, there is no device on the screw to prevent the screw from loosening, which may cause heavy losses. Guangdong Yueluo Hardware Industry Co., Ltd. The inner part will not be loose, and it will save people the trouble of maintenance and reduce the hidden danger of accidents. The solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve its technical problems is to make a special screw and nut, set a stop groove on the screw, and then set a stop rod on the nut. After the screw is tightened , let the backstop rod be stuck in the backstop groove to prevent the screw from loosening. The beneficial effect of Guangdong Yueluo Hardware Industry Co., Ltd. is to ensure that the screws will not loosen during the service period, reducing the hidden danger of accidents and reducing the maintenance rate. Guangdong Yueluo Hardware Industry Co., Ltd. is further described below in conjunction with the accompanying drawings and embodiments
Fan rivets are specially designed for manual installation. They can be pulled in through the holes of the panel or the bottom frame. They are made of elastomer material with good toughness and can be installed quickly even in interference assembly. The design is clever and has elastic function. It is not easy to slide out after being pulled in with the corresponding aperture. The fan rivets are mainly used in the fixing of electronic computer case fans, heat sinks and chips, with anti-vibration and noise reduction.
In the past production, gaskets were generally obtained from two channels: first, standard gaskets were mostly purchased from the market, and the cost was high; non-standard gaskets, due to the small demand, required separate tooling and molds, which were expensive and long production cycle. It is difficult to purchase; Second, the plate is purchased by the enterprise, and then the washer is formed by the automatic cutting machine. Because the cut nodules and cut marks produced by flame cutting do not meet the requirements for use, the inner and outer diameters need to be reserved 2 ～3mm machining allowance, and then finish the outer diameter and inner diameter by lathe.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hardened steel ISO120, cap nuts, cap nuts, accessories kits, extended bolts, screws, needle roller pins and other products, we can provide you with The right fastener solution for you.
