Service HotlineFasteners are also divided into different types according to different uses, and new types of fasteners are developed according to the needs of special environments to meet the needs of all walks of life. The gasket combination bolt is a common fastening bolt. The combination gasket protects the surface of the connected parts from scratches, disperses the pressure on the connected parts, and has a sealing and anti-loosening effect. It is widely used. With the continuous improvement of requirements, the new zinc-aluminum coating surface treatment has gradually become the mainstream surface treatment process because it meets the environmental protection requirements, the surface is beautiful, and the corrosion resistance strength is higher than that of the zinc-nickel surface treatment.
screw is a type of fastener that cooperates with threaded holes for combining various parts into one assembly and making the parts easy to assemble or disassemble. However, when the assembly containing the screw is used in a special environment, such as outdoor use or use in a liquid environment, there are requirements for preventing the leakage of liquid through the screw joint and preventing the screw from loosening at the screw joint. The screw structure does not have such a function. In the prior art, when there is a need for leakage prevention and loosening of the screw, a rubber washer is usually added between the screw head of the screw and the locking surface of the locked part, or the thread part of the screw is wrapped to prevent Leakage tape and then add anti-loose washers between the screw head of the screw and the locking surface of the locked part, so as to achieve the purpose of preventing leakage and loosening. However, the use of washers not only increases the thickness and weight of the assembly, but also requires an additional process during assembly, which is labor-consuming and labor-intensive. In the process of screwing, it is easy to cause uncertainty to the rubber washers due to the shear stress of the screws. Leakage occurs due to damage and deformation, and the practice of wrapping leak-proof tape around the screw teeth is often prone to damage to the threaded holes.
Stainless steel screws do not necessarily corrode and rust, but that stainless steel screws have a stronger ability to withstand corrosion and rust than iron screws. But stainless steel screws can still rust under certain circumstances. So under what conditions are stainless steel screws prone to rust! What is the cause of rust? Stainless steel screws have better characteristics, strong corrosion resistance, high temperature resistance, and strong rust resistance. But it will rust in harsh environments. For example, stainless steel screws are exposed to the sun and the wind every day under very humid conditions. Over time, it will definitely rust a little. For example, in contact with some acid-base chemicals to cause chemical reactions. cause corrosion and rust. There are also bad stainless steel screws, such as stainless steel SUS201 screws used in seawater. Due to long-term immersion, SUS201 stainless steel screws themselves are not suitable for use in salty seawater. cause corrosion and rust. For the use of marine products, it is generally recommended to use stainless steel SUS316 screws, because 316 stainless steel screws have better performance such as corrosion resistance. From the above, it can be concluded that stainless steel screws will still corrode and rust under certain circumstances. Therefore, this requires the rational use of stainless steel screws. Use stainless steel screws of different materials in different situations. And in different occasions, when using stainless steel screws, special attention is also required, and some details need to be considered more. Try to control the corrosion and rust of stainless steel screws as much as possible.
All-aluminum blind rivet The body of the rivet is also made of high-quality aluminum wire, which is beautiful and durable after riveting and will never rust: Compared with ordinary blind rivets, rivets have lower riveting strength and are suitable for connectors with relatively soft materials. . Split Stainless Steel Rivet: This rivet is a high-tension, corrosion-resistant choice. Round head rivets are mainly used in riveting occasions subject to large lateral loads, and are the most widely used. Flat cone head rivets are often used in riveting occasions with strong corrosion such as ship hulls, boiler water tanks, etc.
In general, the size, mechanical properties and working performance requirements of self-tapping screws have the following standards: 1. Self-tapping screw size standard ASME B18.6.3 2010 standard not only introduces the dimensions of slotted and cross-recessed self-tapping screws and metal drive screws, but also includes the mechanical properties and work performance requirements of carbon steel self-tapping screws. The appendix gives instructions for measuring the various dimensions and application guidance on clamping lengths and test apertures. 2. Self-tapping screw performance standards (including mechanical properties and work performance): (1) SAE J933: Introduces the mechanical performance and work performance requirements of carbon steel ordinary self-tapping screws and white-cut self-tapping screws. The requirements for selection of raw materials, heat treatment, depth of carburized layer, surface hardness, and core hardness are further specified. (2) SAE J81: The mechanical properties and working performance of self-extrusion self-tapping screws (self-tapping locking screws) are introduced. (3) SAE J78: The mechanical properties and working properties of self-drilling and self-tapping screws are introduced. (4) IFl-113: The mechanical properties and working properties of self-drilling and self-tapping screws are introduced. (5) ASTM C1513: Introduces the mechanical properties and performance requirements of carbon steel self-tapping screws. For other special types of self-tapping screws, there is no corresponding national or industrial standard, and no data for self-tapping screws made of other metal materials other than carbon steel have been recognized. For technical data on these self-tapping screws, you can check with the manufacturer.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: square inclined flat washers, screw connection screw caps, T-slot pressure plate nuts, Yueluo brand nuts and other products, we can provide you with products suitable for you fastener solutions.
