Service HotlineStainless steel screws, as the name suggests, must be made of stainless steel screw wire, and then screw the screw thread. Many of the properties of stainless steel screws are related to stainless steel. Taking into account the properties and organization of stainless steel, understand the properties of stainless steel materials and other aspects. Therefore, it is understood that stainless steel has good mechanical properties such as anti-rust, anti-corrosion, high temperature resistance, etc., then stainless steel screws also have these good mechanical properties. With the increasing quality of stainless steel materials. The mechanical properties of stainless steel screws produced by the screw industry are getting better and better. Anti-rust, anti-corrosion ability, and high temperature and high pressure are getting stronger and stronger.
The semicircular key is a kind of key, the upper surface is a plane, the lower surface is a semicircular arc surface, the two sides are parallel, commonly known as the crescent key. It is basically the same as the flat key connection method, but it is more convenient to manufacture and disassemble than the flat key, and is especially suitable for the connection between the tapered shaft and the hub. The half-round key transmits torque on the side, but the keyway is deep, which weakens the shaft greatly. Due to the deep keyway, the bottom of the keyway is easily deformed after the shaft is heat treated. Therefore, when the semicircular key and the keyway are assembled in a transitional fit relationship, the interference between the lower part of the semicircular key and the bottom of the keyway often occurs, resulting in difficult or impossible assembly. Assembly situation. In order to solve the above technical problems, the current method is to make the thickness of the semicircular key appropriately thin, so that the semicircular key and the keyway are clearance fit, which brings about a large gap between the upper part of the semicircular key and the keyway, and the semicircular key is in operation. Difficult to locate in the keyway, affecting smooth transmission.
The bolt thread is generally cold worked, so that the thread blank within a certain diameter range passes through the rubbing (rolling) wire plate (die), and the thread is formed by the pressure of the wire plate (rolling die). The plastic streamline of the threaded part is not cut off, the strength is increased, the precision is high, and the quality is uniform, so it is widely used. In order to make the outer diameter of the thread of the final product, the required thread blank diameter is different, because it is limited by factors such as thread accuracy and whether the material is coated or not. Rolling (rubbing) thread is a processing method that uses plastic deformation to form thread teeth. It uses a rolling (screwing plate) die with the same pitch and tooth shape as the thread to be processed, while extruding the cylindrical screw blank, while rotating the screw blank, and finally transferring the tooth shape on the rolling die to the On the screw blank, the thread is formed. The common point of rolling (rubbing) thread processing is that the number of rolling revolutions does not need to be too much. If it is too much, the efficiency will be low, and the surface of the thread teeth will easily cause separation or random buckle. On the contrary, if the number of revolutions is too small, the diameter of the thread is easy to be out of round, and the pressure at the initial stage of rolling increases abnormally, resulting in a shortening of the life of the die. Common defects of rolled threads: cracks or scratches on the surface of the thread part; random buckles; out of roundness of the thread part. If these defects occur in large numbers, they will be discovered during the processing stage. If the number of occurrences is small, the production process does not notice these defects and then circulates to users, causing trouble. Therefore, the key issues of processing conditions should be summarized, and these key factors should be controlled in the production process.
Screw (pinyin: luógǎn, English: screw): a cylinder with a spiral groove cut on the outer surface or a cone cut with a tapered spiral groove. The screw has a different head, the head is called an external hexagon screw. There are others, such as large flat screws, socket head screws and so on.
Most of the capacitors on the market have two pins, which are the connection terminals of the positive and negative electrodes of the capacitor. At present, there is a big hidden danger in these capacitors, that is, the connection between the pins and the core inside the capacitor is basically a stick-on connection. When the capacitor is working, the internal temperature rises rapidly, and the stick-type connection is unstable after being heated, and it is easy to detach Or loose.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: processing cone pins, stainless steel hexagon extended nuts, hexagon with intermediate nuts, 8.8 black nuts and other products, we can provide you with suitable products Your fastener solution.
