Service HotlineThe middle pins on upright and horizontal pianos are also called balance pins. The middle pins are installed on the middle sleepers of the keyboard frame and play the role of fixing the keys. Generally, there are 88 keys in the piano. The pins are matched with the pin holes, and the keys are installed on each middle pin one by one through the pin holes. Due to the large number of middle pins and keys, in the production and installation process, in order to ensure the flatness of the 88 keys after installation, it is necessary to debug the middle pins and keys one by one, or add paper circles to the middle fixed part on the middle pins. The flatness of the 88 keys is kept the same. This debugging method is extremely cumbersome and increases the workload of debugging. Moreover, when adding paper circles, the keys need to be disassembled frequently. Due to the limitation of the installation space of the keys, it is troublesome to disassemble the keys, and it is easy to install and disassemble the keys many times. Damage to the pin holes on the keys, degrading the quality of the piano.
Equipment that needs to be maintained at high altitude or under complex working conditions requires screw loss prevention design. Although traditional captive screws can achieve the purpose of preventing falling off, because the diameter of the screw is smaller than the major diameter of the thread, it is difficult to match the gasket, and the gasket will be eccentric, which is easy to install. Scratch the surface of the product, affecting the corrosion resistance and appearance of the product.
A rivet is a part that uses its own deformation or interference to connect the riveted parts in riveting. With the continuous progress and development of science, rivets have been used in many occasions because of their convenient use and reliable connection. The rivet includes a nail head and a stem. The traditional processing mold for the rivet head includes a base, and a nail head forming part is arranged on the base. However, due to the limited service life of the mold, the processing mold of this structure is replaced. It needs to be replaced together with the base, which is a waste of material, which increases the production cost, and the rivet itself is relatively cheap, so this reduces the profit of the enterprise.
The inch thread is the thread size marked in inch. According to the shape, it is divided into two types: cylindrical and conical; according to the tooth angle, it is divided into two types: 55° and 60°. The 1/4, 1/2, 1/8 marks in the thread refer to the diameter of the thread size in inches. One inch equals 8 cents, 1/4 inch equals 2 cents, and so on.
When the mold is manufactured, many positioning pins need to be installed to fix the relative position between the two parts. The positioning pins are usually sunk into the positioning pin holes on the mold. Since the mold needs to be pulled out frequently during assembly, in order to Remove the parts and make corrections. At the same time, the mold also needs to pull out the positioning pins during maintenance to remove the damaged parts for maintenance. Therefore, the workload of pulling the pins is large. The existing methods are: 1) When installing the pins, The operator uses a self-made long screw that matches the threaded hole of the pin to screw it into the pin, and then aligns the pin hole with a hammer to hit the screw to make the pin snap in, and then screw the screw out by hand. The disadvantage is: on the one hand, the hammer hits the screw It is easy to cause the screw to be damaged or deformed, and it cannot be used normally. On the other hand, it is labor-intensive to remove the screw by hand and may not be able to be removed; 2) When pulling out the pin, the operator will screw the screw into the pin and use force directly or with pliers To pull out a screw, a few companies use a large pin puller to pull it out. The disadvantage is that it is too laborious and time-consuming to pull out by hand or with pliers. Even if a large pin puller is used, the weight of the pin puller itself is large. , it is inconvenient to use.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: wing nuts, trimmed outer hexagon bolts, high-strength hexagon flange nuts, DIN799 bolts and other products, we can provide you with suitable tightening. Firmware Solutions.
