Service HotlineReferring to Figure 1, one end of the existing insert nut 1' is embedded in the injection molded part 2', and the other end is exposed to the injection molded part 2'. The insert nut 1' has opposite lower and upper end surfaces in the axial direction. The end face of one end of the insert injection molded part 2' is the lower end face. In order to reduce the resistance during hot pressing, the connection between the inner wall surface and the lower end surface of the insert nut 1 ′ is provided with an inclined surface. However, when the embedded nut 1' of this structure is hot-pressed, the hot melted glue will generate a shunt that rises along the slope, and then a convex peak is formed in the screw hole of the embedded nut 1', and the convex peak occupies the screw. The space in the hole prevents the screw 5' from being completely screwed in; at the same time, due to the shunting of the hot solder, the knurling of the inner nut 1' near the upper end face cannot be filled with the solder, which makes the inner nut 1' and the inner nut 1' and The injection part 2' is not firmly embedded. Therefore, the locking strength of the existing insert nut 1 ′ and the screw 5 ′ after being hot-pressed is relatively low.
At present, most of the cylindrical pin press-fitting is to put the product into the positioning position of the lower die first, and then take a cylindrical pin and put it into a cylindrical pin positioning hole that is concentric and perpendicular to the hole in which the product is pressed, or put it on the product. , the pin needs to have a positioning guide; or it is fixed on the top of the indenter so that it will not fall, and then the press is completed. In fact, it is difficult to press the small cylindrical pins. To ensure the good quality of the product, it is required to locate accurately, to ensure that the cylindrical pins are concentric and vertical, and to put the cylindrical pins one by one. It is very easy for workers to produce. Fatigue and low efficiency, product quality control is affected by many human factors, resulting in unstable product quality and certain safety hazards in work. On the other hand, in some production lines, the cost of the press-in cylindrical pins is relatively expensive, such as finger cylinders and moving mechanisms, which will put a lot of cost pressure on the equipment investment of small and micro enterprises.
Guangdong Yueluo Hardware Industry Co., Ltd. discloses a low-carbon steel rivet nut fastened to a thin-walled and thin-plate fastener. The rivet nut fastener is composed of a brim, a deformed skirt, and a threaded hole. Using low carbon steel cold extrusion, the brim is formed by cold heading, the deformed skirt is extruded in the concave die, and the thread hole of the nut tapping skirt is extruded at the lower end of the deformed skirt. It is characterized in that there are fish teeth under the brim; the outer side of the lower end of the threaded hole has a lead angle; the cross-section of the thread of the inner wall of the threaded hole is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave solitary shape, and the fastener does not need to be welded. , Single-sided riveting, easy operation and firm connection.
Iron pans are traditional kitchen utensils for people to cook food. They generally do not contain toxic substances and will not oxidize. In the process of stir-frying and cooking food, there are very few dissolved substances in the iron pot. Even if there is iron dissolved out, it is also good for the human body. Cooking in the iron pot is the most direct way to supplement iron. The main types are India pot, ear pot, pan, oil pan, pancake pan. In the process of cooking dishes in an iron pan, a small amount of iron will dissolve in the food, supplement iron for people, supplement the iron-deficient part of the food itself, and play a role in preventing iron-deficiency anemia. Can increase the amount of iron in a person's diet. Therefore, as far as the prevention and treatment of iron deficiency anemia is concerned, cooking in an iron pan is beneficial to health.
Rivets are mostly used for fixed riveting and movable riveting between parts. The rivets used for movable riveting are mostly cylindrical, and there is no size limit for riveted parts, which is easy to cause parts to be squeezed and deformed during riveting. For example, The parts are inserted into the parts for active riveting. When riveting, the riveting force can easily cause the parts to clamp the parts, which in turn causes difficulty in the movement of the parts and the parts, high operating force and noise problems, and the parts are easily damaged.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: pattern saddle gasket, national standard T-nut, large supply, carbon steel grade 8.8 bolts and other products, we can provide you with suitable products for you fastener solutions.
