Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a cement screw that is easy to install and can be removed in view of the shortcomings of the above-mentioned cement nails that cannot be disassembled and the expansion screws are not easy to install for the first time. Guangdong Yueluo Hardware Industry Co., Ltd. is a cement screw, which is realized by the following technical solutions. The cement screw is composed of a nail tip and a nail body. There is a thread at the back of the nail body. This thread can be an internal thread or an external thread. . When using, use a hammer to drive cement screws into the cement, and you can use ordinary screws or nuts to freely screw in and out to install and fix objects. Compared with the existing technology, Guangdong Yueluo Hardware Industry Co., Ltd. has the advantage that there are internal threads or external threads on the back of the cement screw, so it is not only easy to install for the first time, but also the objects to be installed can be disassembled repeatedly. Used as a fastener when installing objects on cement that may need to be dismantled.
Blind rivets are a type of rivets for single-sided riveting, but they must be riveted with a special tool - a rivet gun (manual, electric, pneumatic). This type of rivet is especially suitable for riveting occasions where it is inconvenient to use ordinary rivets (which must be riveted from both sides), so it is widely used in construction, automobiles, ships, aircraft, machinery, electrical appliances, furniture and other products. Among them, the open type oblate head blind rivets are the most widely used, the countersunk head blind rivets are suitable for riveting occasions that require smooth performance, and the closed blind rivets are suitable for riveting occasions that require higher load and certain sealing performance.
It can be seen that the above processing method can only be used to process a relatively simple retaining ring (that is, only a ring body, which cannot be cut or punched), and the outer surface of the processed retaining ring still cannot be guaranteed to be completely flat.
Bolts are widely used as common fasteners. The traditional T-bolt consists of a head, a screw and a tail. The head is a long plane. During the use of the T-bolt of this structure, the T-bolt and the groove The contact surface of the track is a smooth surface, its friction force is not large, its connection is not firm enough, and it is easy to fall off. For this reason, some people design the head as a bevel to increase friction, but only one bevel is in contact with the part in this design, and the sealing is not very good
Now the screw itself is made of metal, so it is easy to rust, especially screws in harsh weather environments that are exposed to the air for a long time, such as air conditioners, wires, etc. In the existing technology, the shape of the screw has been fixed, and the structure of the screw itself is composed of a shaft with twill in the middle and a polygonal structure with stripes on the outside. OK, but because of the installation of some equipment, it needs to be exposed to the air for a long time. For example, the outdoor unit of the air conditioner must be installed in the outdoor area, and the outdoor can not be sheltered from wind and rain, so after long-term sun and rain, the screw The surface is easy to rust. If the rust is serious to a certain extent, the nut will be embroidered to death. Once the external machine needs to be disassembled one day, the embroidered screw will lose its use value and give workers to the workers. The disassembly and assembly of the screw has caused a lot of trouble, because the embroidered screw cannot be unscrewed directly. The only method used is to cut off the shaft in the middle of the screw with a hacksaw, or discard the entire screw structure. Since the shaft in the screw has been inserted into the middle of the wall, this waste is not good for both aesthetics and safety. To solve the rust problem of the screw, the existing technology is to improve the material of the screw, or to maintain it regularly, but this method itself is time-consuming and labor-intensive, and it is a waste of resources.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB869 rivets, extended cup head hexagon socket screws, toothed non-slip screw caps, non-return non-slip nuts and other products, we can provide you with products suitable for you fastener solutions.
