Service HotlineIn actual use, the rivet rod body 3-2 is passed through the riveting plate 6 and the riveting plate 7, and the rivet dome head 3-1 is placed in the mold cavity 1-1, and the cover mold 2 is driven by the riveting machine to impact the rivet rod body 3-2. Because the center of the cover mold 2 is provided with a cavity 2-1 that matches the shape of the rivet dome 3-3, the end of the rivet rod 3-2 will form the rivet dome 3-3. However, due to the rivet When the riveting machine is impacted and vibrated, a large amount of oxide slag 4 will be generated, and the oxide slag 4 will slide down the surface of the cavity 1-1 to the bottom of the cavity 1-1 and accumulate. At this time, the temperature of the rivet is very high and the plasticity is very good. The hardness is extremely low and it is easy to form. Therefore, the accumulated oxide slag 4 squeezes the surface of the rivet dome 3-1 and the bottom surface of the cavity 1-1 to form pits, and causes wear on the bottom surface of the cavity, not only It affects the riveting quality, riveting strength and appearance quality of the rivet, and also affects the quality of the rivet die, resulting in economic losses.
In order to solve the problems existing in the prior art, Yueluo Company provides a fastener that prevents the nut from falling off. After the nut is installed in place, a locking strip can be inserted into the groove of the bolt to lock the nut, so that the nut can be locked. It cannot be loosened to prevent the nut from falling off. If the nut needs to be removed, the nut can be removed normally after removing the locking strip.
The above riveting requires special tools and equipment, which cannot be used in actual specific occasions. In the case of no electricity and no air, only manual tools can be used; and manual tools cannot be used for large types of rivets due to limited human strength. Moreover, after the rivet is disassembled, the rivet itself will be destroyed and cannot be reused.
In order to overcome the technical problem that the screws and nuts cannot be disassembled and assembled at the same time in the prior art, Guangdong Yueluo Hardware Industry Co., Ltd. provides a simple structure and can be quickly disassembled and assembled at the same time in a small space. screw and nut removal tool.
Commonly used screw materials in my country are No. 45 steel, 40Cr, ammoniated steel, 38CrMOAl, superalloy, etc. 1) No. 45 steel is cheap and has good processing performance, but poor wear resistance and corrosion resistance. Heat treatment: quenched and tempered HB220-270, high-frequency quenched HRC45--48. 2) The performance of 40Cr is better than that of No. 45 steel, but it is often plated with a layer of chromium to improve its corrosion resistance and wear resistance. However, the requirements for the chrome plating layer are relatively high. If the plating layer is too thin, it is easy to wear, and if it is too thick, it is easy to peel off. After peeling off, it will accelerate the corrosion, and it has been rarely used. Heat treatment: quenched and tempered HB220—270, hard chrome plated HRC>553) nitrided steel, 38CrMoAl have excellent comprehensive properties and are widely used. Generally, the nitride layer reaches 0.4-0.6 mm. However, this material has low resistance to hydrogen chloride corrosion and is relatively expensive. 4) The superalloy material is superior to other materials. This material does not need coating, and is mainly used for the raw halogen-free screw of injection molding machine. The material has high oxidation resistance and corrosion resistance.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagon socket bolts, cross flat head bolts and nuts, plum blossom retaining rings, large flat head semi-circle head square neck bolts and other products, we can provide you with suitable products. Your fastener solution.
