Service HotlineHere Yueluo eliminates the drawbacks. The purpose of Yueluo is to provide a locking screw by which the gap existing between the locking screw and a transverse hole in a locking screw can be eliminated. Yueluo achieves the proposed object with a locking screw, which has the features of claim 4 . The line connecting the centers of gravity of the respective axially continuous orthogonal cross-sectional areas of the locking screw is regarded as a line. The advantage achieved by Yueluo can basically be seen that, due to the locking screw of Yueluo, the gap between the horizontal hole of the screw and the locking screw can be eliminated. Other advantages are as follows - the insertion accuracy and surgeon time spent remain within the range to date; - the strength of the locking screw is maintained; and - the extraction of an expired broken screw is assured. The further composition of Yueluo and Yueluo is explained in more detail below by means of schematic diagrams of parts of various embodiments.
Standardized mechanical parts for fastening connections. Standard fasteners mainly include bolts, studs, screws, set screws, nuts, washers and rivets. There are many structural types of bolts, and most of the heads are hexagonal. For bolts subjected to shock, vibration or variable load, in order to increase flexibility, the polished rod part is made into thin sections or hollows. The seat end of the stud is screwed into the threaded hole of the connected piece, and the nut used at the nut end is similar to the bolt nut. The structure of the screw is basically the same as that of the bolt, but the shape of the head is various to adapt to different assembly spaces, tightening degrees and connection appearances. Set screws have different head and tip shapes to accommodate different levels of tightening. Nuts are also available in a variety of styles, with hexagons being the most widely used.
At present, in the standard cabinets of computers, networks, automation, etc., to fix the equipment in the cabinet, it needs to be fixed by using fasteners. The nuts in the existing fasteners are ordinary nuts, which are internal card structures. , there are the following shortcomings: 1. The installation and disassembly are complicated, and a large amount of force is required to insert the nut during installation and disassembly, and the nut cannot be installed and disassembled at all due to the processing error of each nut; 2. After the nut is used for a long time, the nut The card edge will have slack problem, which will affect the use; 3. Installation or disassembly is easy to cause problems such as falling, which may cause electrical short circuit, etc., and there are potential safety hazards; 4. The efficiency of equipment installation is low.
T-slot bolts refer to the bolts installed in the T-slot. The installation process of T-slot bolts is usually as follows. When the T-slot (generally refers to the T-slot aluminum alloy profile) is set horizontally, the bolt The bolt head is placed in the T-slot in the horizontal direction, the bolt shaft is facing outward, and then the bolt is rotated 90 degrees axially, the bolt head becomes vertical and will not come out of the T-slot, and then install the mounting hole of the object Align the bolt rod and insert it and screw the nut on the bolt rod. During the tightening process of the nut, if the thread gap is small or the thread is damaged or there is dirt, the bolt will often rotate, and the rotation angle of the bolt is uncontrollable and impossible. Observe that when the rotation angle of the bolt is in the range of about 90 degrees, the bolt is in a state of being released from the T-shaped groove at any time. Even if the nut is tightened, the installation of the installation object is invalid and unreliable, and there is a serious safety hazard. , the actual situation is that when the rotation angle of the bolt exceeds 20-30 degrees, the installation of the installation object is already unreliable.
Friction type high-strength bolts: suitable for beam and column connections of steel frame structures, solid web beam connections, heavy-duty crane beam connections in industrial plants, braking systems and important structures bearing dynamic loads. Pressure-bearing high-strength bolts: Can be used for shear connections in statically loaded structures that allow a small amount of sliding or in members that are indirectly loaded with dynamic loads. Tensile high-strength bolts: When the bolts are in tension, the fatigue strength is low. Under the action of dynamic load, its bearing capacity is not easy to exceed 0.6P (P is the allowable axial force of the bolt). Therefore, it is only suitable for use under static load. Such as flange butt joints, T-joints, etc. of pressure members.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: plate rivets, external hexagon bolts, socket head plug bolts, aluminum alloy double internal teeth and other products, we can provide you with suitable fastening products piece solution.
