Service HotlineIn the process of electronic accessories such as mobile phones and computers, especially multi-layer circuit boards, there are generally fixed connections between multi-layer circuit boards or other components. At present, there are two main connection methods. One is to use laser welding. However, the laser welding equipment is expensive and has very high requirements on the position of the weldment. Therefore, during welding, it must be ensured that the final position of the weldment needs to be the same as the laser beam will impact. Solder joint alignment. The other is to use a metal rivet to pass through the positioning hole, and then impact the rivet with a punching needle, so that the open end of the rivet is deformed and opened and pressed on the fixed piece to form a rivet fixed state. However, in actual operation, when the open end of the rivet tube is opened and deformed by the impact, strong cracking often occurs, resulting in a small amount of conductive fracture debris, which falls on the circuit board or other devices to be connected, causing Short circuit, in view of this shortcoming, some manufacturers have changed the metal rivets to plastic materials, but the plastic rivets have poor ductility and often break when impacted with a punching needle, resulting in the failure to achieve the riveting fixing force of the original metal rivets. In addition, the above two fixing methods are complicated in operation and low in installation efficiency.
People often think that magnets attract stainless steel to verify its pros and cons and its authenticity. If it does not attract non-magnetism, it is considered to be good, and it is genuine; if it is magnetic, it is considered to be counterfeit. In fact, this is an extremely one-sided, unrealistic and wrong identification method. There are many kinds of stainless steel screws, which can be divided into several categories according to the organizational structure at room temperature: 1. Austenite type: such as 304, 321, 316, 310, etc.; 2. Martensite or ferrite type: such as 430, 420, 410, etc.; Austenite type is non-magnetic or weakly magnetic, and martensite or ferrite is magnetic. Most of the stainless steel usually used for decorative tube sheets is austenitic 304 material, which is generally non-magnetic or weakly magnetic, but may also appear magnetic due to fluctuations in chemical composition or different processing conditions caused by smelting, but this cannot be considered as a Counterfeit or substandard, what is the reason for this? As mentioned above, austenite is non-magnetic or weakly magnetic, while martensite or ferrite is magnetic. Due to component segregation or improper heat treatment during smelting, a small amount of martensite or ferrite in austenitic 304 stainless steel will be caused. body tissue. In this way, 304 stainless steel will have weak magnetism. In addition, after cold working of 304 stainless steel, the structure will also be transformed into martensite. The greater the cold working deformation, the more martensite transformation, and the greater the magnetic properties of the steel. Like a batch of steel strips, Φ76 tubes are produced without obvious magnetic induction, and Φ9.5 tubes are produced. The magnetic induction is more obvious due to the large deformation of the bending and bending. The deformation of the square rectangular tube is larger than that of the round tube, especially the corner part, the deformation is more intense and the magnetic force is more obvious. In order to completely eliminate the magnetic properties of 304 steel caused by the above reasons, the stable austenite structure can be restored by high-temperature solution treatment, thereby eliminating the magnetic properties. In particular, the magnetic properties of 304 stainless steel caused by the above reasons are completely different from those of other materials such as 430 and carbon steel, which means that the magnetic properties of 304 steel always show weak magnetic properties. This tells us that if the stainless steel strip is weakly magnetic or completely non-magnetic, it should be judged as 304 or 316 material; if it is the same as carbon steel, it shows strong magnetism, because it is judged as not 304 material.
If the above-mentioned nuts and screws are used as a kind of fasteners that can prevent others from being disassembled, such as when installing iron doors-steel windows, people usually tighten the nuts first, and then use a welding machine to weld the nuts and screws. To prevent the nut from loosening, it may be necessary to use a tool to mill the threads on the screw. It can be seen that this approach is very inconvenient.
The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is a kind of anti-loosening cylindrical pin with grooves specially designed for the multi-link transmission paint mixing mixer, which is specially designed for the problems existing in the above-mentioned prior art. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to realize through the following technical solutions: a kind of anti-loose cylindrical pin with groove, wherein: a plurality of axial V-shaped grooves are provided on the cylindrical pin, and the V-shaped groove Arrange evenly on cylindrical pins. There are three to four axial V-shaped grooves on the cylindrical pin. When Guangdong Yueluo Hardware Industry Co., Ltd. is in use, the cylindrical pin with V-shaped groove is installed in the vertical shaft, and cooperates with the U-shaped groove on the connecting rod to transmit torque. The cylindrical pin of the V-groove structure is an interference fit with the mounting hole of the vertical shaft. The biggest feature of Guangdong Yueluo Hardware Industry Co., Ltd. compared with the existing technology is that the cylindrical pin is used as a vertical shaft to connect with the connecting rod for torque transmission, which gives full play to the impact resistance and fatigue resistance of the cylindrical pin. The cylindrical pin has an interference fit with the pin hole, and each edge of the V-groove structure distributed on the cylindrical pin body will penetrate into the inner wall of the pin hole to prevent loosening.
The purpose of Yueluo is to provide a brake pad rivet with shrinkage that can not only solve the problem of normal feeding during assembly, but also save the processing cost of the original machining chamfering and reduce the quality risk of the rivet in use. its production method.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: concave washers, GB70 cylinder head screws, non-slip self-locking nuts, screws and nuts and other products, we can provide you with suitable fasteners for you solution.
