Service HotlineAs the most common hardware, screws and nuts are widely used in construction and machinery fields. However, existing screws and nuts are easily corroded to varying degrees in the natural environment, especially the threads on screws and nuts are corroded After that, the whole screw and nut are useless, and people have to discard them, which will inevitably lead to a lot of waste of resources.
The motor bearing retaining ring is used to fix the axial position of the bearing. The structure of the bearing retaining ring 1 in the prior art is shown in FIG. 1 , which is a ring-shaped sheet-like structure with a gap, the inner diameter of which is smaller than the inner diameter of the connected bearing, and the outer side 11 of the ring is a continuous arc shape. The inner side of the ring is provided with a groove 12, 13 of the same size on both sides of the midpoint of the ring, and the width of the groove is equal to the distance from the groove to the gap of the ring. When the axial locking force (impact) of the bearing retaining ring of this structure is greater than 6.5N, serious deformation will occur or even the retaining ring will be separated from the shaft shoulder. In order to solve this problem, when the axial locking force is greater than 6.5N, the prior art generally adopts a two-ring combined structure of steel wire ring + bearing retaining ring, and its installation state is shown in Figure 2, as shown in Figure 2, l It is a bearing retaining ring in the prior art, 3 is a locking nut, 4 is a fan blade insert, 5 is a bearing, 6 is a shaft, and 7 is a wire ring. However, such a structure is costly and troublesome to assemble, especially if the bearing retaining ring is not placed in place during assembly, the bearing retaining ring is at risk of being crushed.
The purpose of this utility model is to solve the problems in the prior art, and proposes an installation structure which adopts T-bolt and groove matching, which can make the installation of the bolt more convenient, the degree of tightening is higher, the service life is longer, and the Routine replacement and maintenance.
Supporting T-bolts for pre-embedded channels, including hot-rolled pre-embedded channels, the lower part of the pre-embedded channel is provided with a longitudinal opening, and the head of the T-bolt enters from the opening and is clamped in the pre-embedded channel. There are plane teeth at the connection between the buried channel and the T-bolt, and the T-bolt has a tooth-shaped structure matched with the plane teeth. The direction of the teeth is parallel to the slotting direction, and the tooth-shaped cooperation achieves anti-slip effect. However, when the nut tightened on the T-bolt becomes loose, it will cause the T-bolt to move into the embedded channel and lose the toothed fit, thus changing the fixed position of the T-bolt in the embedded channel.
The utility model relates to a connecting piece, in particular to a female and female screw used for shaping products in interior decoration. In the current decoration project, when fixing the decoration stereotyped product, the process is complicated, so labor-intensive and time-consuming, the construction cost is high, and the construction degree is low. For example, the decorative board for fixing the wall, the main process step used in its operation is the leveling of the nail strip. That is to say, saw the wood to the required specifications, then draw horizontal and vertical lines on the wall, and then nail the wooden strips to the wall according to the horizontal and vertical lines, and then glue and glue the board. The first step is to install the lines, color and paint. It can be seen that it is quite troublesome to use the above method to construct. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a female screw, which can skillfully connect decorative products to the wall. As conceived above, the technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is a female screw, which is characterized in that both ends of the screw are threaded, the screw-in end is screwed into the plastic expansion tube inserted into the wall, and the other end of the screw is threaded with the same A female piece is mated and connected. The other end of the screw can also be barb-shaped and directly fit with the decorative board. The screw thread of the screw-in end is a wood thread, and the thread of the mating connection end with the female part is a machine thread.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: aluminum profile diamond nuts, Dacromet hexagon screws, black cross round head bolts, aluminum hex bolts and other products, we can provide you with suitable products for you fastener solutions.
