Service HotlineBy adopting the above technical solution, the setting of the pin cap allows the user to conveniently drive the pin into the pin hole of the workpiece by using a hammer and other power-assisted equipment. Pin hole, the plane of the top contact body relative to the pin cap will collide with the plane where the pin hole is located, the convex body and the pin hole are tightly squeezed, and the pin cannot fall off.
The machinery industry is one of the main users of fasteners. Due to China's late understanding of the important position of mechanical basic parts in the machinery industry and a long-term lack of investment, the entire industry has a poor foundation, weak foundation and weak strength. Especially with the improvement of the level of the main engine in China, the bottleneck phenomenon that the mechanical basic parts lag behind the main engine has become increasingly apparent. Today, although the state has given certain support in technology introduction, technological transformation, scientific research and development, etc., there is still a big gap compared with the current market demand and foreign levels. Unstable quality, high early failure rate and poor reliability. Fasteners are the main basic products in the machinery industry, and the development of the machinery industry also puts forward higher requirements for fastener products. Domestic ordinary standard fasteners have always been in oversupply, while high-end fasteners (high temperature, special-shaped, titanium-plastic composite, special performance and other fasteners) are in short supply, and they also rely on imports. The State Machinery Bureau lists ordinary standard fasteners as restricted development products, and high-strength special-shaped fasteners as currently encouraged development products. With the improvement of the country's industrialization level and technological progress, the use of high-strength fasteners has gradually increased.
The circlip is a common limiting element in the mechanical field, which is mainly used to limit the axial limit of mechanical parts. At present, the common circlips on the market are all circular rings with an opening. The circular ring has a certain elastic deformation capacity. When in use, the circlip can be detachably assembled to the mechanical on the part. However, the defect of the circlip adopting the one-piece ring is that the circlip is easily broken when frequently disassembled and used, and the service life is short.
According to relevant standards, the performance grades of carbon steel and alloy steel bolts are divided into more than 10 grades such as 3.6, 4.6, 4.8, 5.6, 6.8, 8.8, 9.8, 10.9, 12.9, etc. Among them, the bolts of grade 8.8 and above are made of low-carbon alloy steel or medium Carbon steel and heat treatment (quenching, tempering) are generally called high-strength bolts, and the rest are generally called ordinary bolts. The bolt performance grade label consists of two parts of numbers, which represent the nominal tensile strength value and yield ratio of the bolt material respectively. Stainless steel bolts are divided into A1-50, A1-70, A1-80, A2-50, A2-70, A2-80, A3-50, A3-70, A3-80, A4-50, A4-70, A4-80, A5-50, A5-70, A5-80, C1-50, C1-70, C1-110, C4-50, C4-70, C3-80, F1-45, F1- 60. The first letter and number represent the stainless steel group, and the second and third numbers represent 1/10 of the tensile strength. [2]
GB 3098.1 Mechanical Properties of Fasteners Bolts, Screws, Studs and Nuts GB 3098.6 Mechanical Properties of Fasteners Stainless Steel Bolts, Screws, Studs and Nuts GB 3103.1 Tolerances of Fasteners Bolts, Screws and Nuts GB 5267 Electroplating of Threaded Fasteners GB 5779.1 Surface Defects of Fasteners - Bolts, Screws and Studs - General Requirements GB 5779.3 Surface Defects of Fasteners - Bolts, Screws and Studs - Special Requirements
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagonal screws, supply nylon nuts, wholesale cage nuts, sets of screw nuts and other products, we can provide you with suitable fastener solutions for you Program.
