Service HotlineNuts are parts that tightly connect mechanical equipment. Through the inner thread, nuts and bolts of the same specification can be connected together. At present, most nuts are used together with gaskets when they are locked, or are set as an integrated structure, which has the advantage of increasing Friction, strengthen the effect of tightening, but the square nut is usually used directly without adding a gasket, and the upper and lower end faces are flat, very smooth, when subjected to strong vibration, it is very easy to loosen, and the tightening effect is not good.
Some electronic products need to install some plastic parts or protective sleeves for components on the PCB, which need to be fixed by screws. The function of the fixture is to locate the PCB and the required installation parts, and increase the work efficiency. The existing screw fixture is inconvenient According to the needs of the site, the positioning station of the screw can be changed, the accurate positioning of the screw is difficult and the clamping effect of the workpiece is poor. A screw jig is proposed.
The existing spring screw includes a screw rod, a spring connecting sleeve, a spring, a fixed connecting sleeve, a nut and a nut sleeve, wherein the screw rod includes a screw cap, a connecting section without threads and a threaded connecting section with threads, and the connecting section is located in the screw cap and the thread. A shaft shoulder is arranged between the connecting sections and between the connecting section and the threaded connecting section, the connecting section of the screw is sleeved with a spring connecting sleeve, a spring and a fixed connecting sleeve, the spring connecting sleeve is close to the screw cap, and the connecting sleeve is connected between the spring connecting sleeve and the fixed connecting sleeve The connection spring is connected with a threaded nut on the threaded connection section of the screw, and the nut sleeve is connected to the nut sleeve. The fixed connection sleeve is fixedly connected to the upper die of the steel mold through bolts, and the nut sleeve is welded to the lower mold of the steel mold. When clamping the mold, a professional is required to turn the screw from the lower mold to the upper mold or hook it to the upper mold with a foot and then tighten it with the wind, which is inconvenient to install, has low work efficiency, and has potential safety hazards. Contents of the utility model Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. aims to provide a spring screw that is easy to operate. In order to solve the problems existing in the background technology, Guangdong Yueluo Hardware Industry Co., Ltd. adopts the following technical scheme: a spring screw, including a screw rod, an upper compression spring washer, a spring, a fixed sleeve, a lower compression spring washer, Base and fixing nut. The screw rod includes a screw cap, a connecting section without threads and a threaded connecting section with threads, the connecting section is located between the screw cap and the threaded connecting section, and a shaft shoulder is arranged between the connecting section and the threaded connecting section. The connecting section of the screw rod is sleeved with an upper compression spring washer, a spring, a fixing sleeve, a lower compression spring washer and a base, and the threaded connection section is connected with a fixing nut. A fixed sleeve is sleeved between the connection section and the threaded connection section, and the fixed sleeve is sleeved with a lower pressure spring washer and a base. The upper compression spring washer is close to the screw cap, the lower compression spring washer is fixed on the base by four screws, the spring is placed between the upper compression spring washer and the lower compression spring washer, and one end of the spring is sleeved with the upper compression spring washer , and the other end is sleeved with a fixed sleeve. For Yueluo, the diameter of the spring screw is between T20-T27. In this preferred solution, the use performance of the spring is high, which is beneficial to prolong the service life of the spring screw. For Yueluo, preferably, the thread connecting section of the screw adopts T-shaped thread. In this preferred solution, the fixing nut is tightly matched with the threaded connection section, so that the steel mold is clamped tightly. Yueluo is preferably made of 40Cr material for the fixing nut and screw. In this preferred solution, the rigidity of the fixing nut and the screw rod is high, which is beneficial to improve the usability of the spring screw. Yueluo is preferred, the spring screw parts except the fixing nut and the screw rod are made of 47# steel material. In this preferred solution, the production cost is low. In summary, Guangdong Yueluo Hardware Industry Co., Ltd. brings the beneficial effects: when the spring screw is used, it is only necessary to use a wrench to move the fixed nut, which is convenient for installation, disassembly and replacement, improving work efficiency and reducing production costs.
The advantages of the pressure riveting nut: 1. The length guarantee of the distance range is realized, which greatly simplifies the assembly process and speeds up the production progress of the assembled spacing panel and accessories; 2. The back of the plate is completely embedded and flat, while ensuring the head of the nut column The plane is smooth with the plate; 3. The raw material is free-cutting iron or free-cutting stainless steel; the technical guide for the application of the pressure riveting standoff: 1. When selecting the standoff, it must be based on the thickness of the plate used, the exact size range, and the hardness of the low-carbon steel plate must be less than 70RB, the hardness of stainless steel plate must be less than 80RB. 2. The surface of free-cutting iron is treated, and the stainless steel maintains its original color. Users can order according to the model and specifications in the table according to their needs, or they can also make special orders according to their needs. 3. The hole size of the plate must be processed according to the tolerance size of 0-+0.075mm, and punching is recommended. 4. The installation must be realized by press riveting operation, and it must not be knocked in by impact. 5. When the material is stainless steel, the tail number should be marked with S. 6. The end face of the nut column is represented by C. 7. The length of the through-hole nut column is full wire below 10mm. If it is above 10mm, it can be reamed on the hexagonal end face (type I) or the round end face (type II).
Cylindrical pins are widely used for positioning or connecting components on mechanical equipment, and the cylindrical pins are fixed in the pin holes by means of interference fit. Cylindrical pins are generally processed by a grinding machine and a punch former, but the above processing methods have complex operation procedures, high processing equipment and high processing costs.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: stud bolts, nylon rubber ring nuts, small countersunk head rivet nuts, IN949 stud bolts and other products, we can provide you with suitable products Your fastener solution.
