Service HotlineYueluo relates to a self-tapping screw according to the preamble of claim 1. A self-tapping screw is known from EP0623759B1, the ratio of the outer diameter to the smaller diameter of the self-tapping screw is about 1.25-1.5, the ratio of the outer diameter to the pitch lead is about 1.5-1.6 and the thread The flank angles of , are < 50° and ≥ 35°. EP0433484B1 proposes a self-tapping screw whose thread is provided with cutting teeth of approximately arcuate design, and the cutting edge and the thread crest are at the same horizontal position and are set in opposite directions. One purpose of Yueluo is to realize a general type of self-tapping screw so that it can be screwed particularly easily into holes drilled in concrete or other materials such as bricks and the like. According to Yueluo, this object is achieved by the features in the characterizing part of claim 1, and surprisingly, it has been found that the parallel arrangement of the flanks, ie with a flank angle of about 0°, will make screwing particularly easy when screwing in , especially if the diameter of the hole varies within an allowable tolerance. One reason may be due to the fact that there is no lateral pressure on the material screwed into the thread, even if threads of different depths are cut in concrete or other materials such as brick, chipped plywood, or hardwood. The thread cuts into the material over its entire width by cutting grooves. In particular according to the embodiment of claim 11 the result is that the material cut out when screwing in the screw can be discharged without any accumulation, the dependent claims reflecting many advantages of further embodiments.
Currently, the method of fixing objects on cement is with cement nails or expansion screws. Cement nails are objects made of hard alloy steel that look like iron nails, which are composed of nail tips and nail bodies. Cement nails are hammered into the cement. Cement nails are easy to drive in, but not removable. The expansion screw is composed of a large end screw, a slotted sleeve, a gasket, a spring washer, and a nut. When using, first drill a hole in the cement with an electric hammer, put in the expansion screw, and tighten the nut to make the slotted sleeve expand at the tail of the big tail screw, so as to fix the expansion screw on the cement. At this time, unscrew the nut to install a fixed object on the expansion screw. Although this method can be disassembled, an electric hammer is required for the first installation, which is inconvenient.
In many national standards, there will be a division of intensity levels. Combination screws are no exception. The strength grade of the combined screw is divided according to the material of the screw wire and the hardness index of the screw wire. General combination screw materials are divided into stainless steel and iron, stainless steel is divided into stainless steel 201, stainless steel 304 and stainless steel 316 and so on. Iron is divided into three types: low carbon steel, medium carbon steel, and high carbon steel. Carbon steel combination screws refer to iron combination screws. Generally, iron combination screws are classified into grades 4.8, 8.8, 10.9, and 12.9. However, the combination screws of grade 10.9 and grade 12.9 are rarely used in the market, so we will not talk about them here. And the combination screws on the market are more commonly used combination screws of grade 4.8 and 8.8. 4.8 grade combination screws are generally made of 1010A screw wire rods. After the screw wire rods are beaten into screws, they are combined with spring flat washers. After production, this 4.8 grade combination screw does not need to be hardened. Its hardness can reach 4.8. 8.8 grade combination screws are generally made of screw wire 10B21 piers. After the screw and wire piers are made into screws, they are equipped with spring washers and flat washers. They can pass through the automatic elastic flat washer machine to rub the three pieces together. Fasten the spring-flat washer combination on the screw, and the spring-flat washer will not fall off. After the combination screw is produced, it needs to be hardened to make the hardness reach 8.8. After the hardness reaches 8.8, we need to take it for electroplating. In order to prevent hydrogen embrittlement of the spring washer in the 8.8-level combination screw with added hardness, it is easy to break. In this way, we have to perform hydrogen removal treatment on the hardened combined screws, and only after the hydrogen removal can be plated. In short, there are many kinds of standard grades of combined screw strength, but generally only two types are used in the market, one is the 4.8-level combined screw strength, and the other is the 8.8-level combined screw strength. 4.8-level combination screws are the most used in the market and customer needs, and have a wide range of applications. As for the standard strength of 8.8-level combination screws, we generally refer to 8.8-level hexagon socket head combination screws, 8.8-level pan head combination screws, and 8.8-level external hexagon combination screws. These three are more commonly used.
With the rapid development of China's machinery industry, especially the development of heavy industry, the demand for large-scale metal processing equipment is increasing; at the same time, higher requirements are also placed on the technical parameters of the equipment. For some large-scale CNC equipment, to ensure the machining accuracy of the whole product, it is not only necessary to rely on high-performance components such as full closed-loop control and precision transmission components, but also requires the positioning and stability of the joint surfaces between the large and medium-sized components of the equipment. The common positioning of the joint surface between large components adopts flat key positioning, and this method requires processing the keyway at the joint surface of the large components. Since the joint surface of large parts is affected by factors such as processing and splicing, it cannot guarantee that the keyways on the large parts combined can be matched according to the theoretical requirements. Therefore, the positioning flat key needs to press the flat key in the two parts of large parts. Different repair allowances Trim into a stepped shape. The height difference of this keyway in different large components makes a single flat key need to be repaired on four sides, which increases the difficulty of the key repair process and makes it difficult to improve work efficiency. Not only that, when the flat key is repaired and assembled, it must be in an interference fit with the keyway, which makes the disassembly and assembly of the flat key more laborious.
During the tightening process of the screw, do not use excessive force, otherwise the product will be damaged. The traditional bolt locking adopts manual operation, which is inefficient and insufficient force. In the existing screw locking device, before locking the screw, the locking force of the screw is tested, but the test equipment is set separately, resulting in a complicated structure. In addition, in the existing screw locking device, when the screw is locked, the position of the screw hole is not corrected, so that the screw often causes damage to the product during the tightening process.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head full hexagonal closed pull female pull cap nuts, wood lock nuts, connection isolation supports, round head pins and other products, we can provide you with The right fastener solution for you.
