Service HotlineThe maximum unscrewing torque of the lock nut is affected by many factors. For the research on the low-cycle fatigue performance of the lock nut, the pitch diameter of the thread, the helix angle and the bevel angle of the thread remain unchanged. Only the maximum elastic restoring force FNmax and the equivalent friction angle ρe of the thread piece will appear to a certain extent after repeated use. Change. Therefore, it is only necessary to analyze the variation law of the maximum unscrewing moment when the lock nut is subjected to cyclic load from these two aspects.
At present, in the standard cabinets of computers, networks, automation, etc., to fix the equipment in the cabinet, it needs to be fixed by using fasteners. The nuts in the existing fasteners are ordinary nuts, which are internal card structures. , there are the following shortcomings: 1. The installation and disassembly are complicated, and a large amount of force is required to insert the nut during installation and disassembly, and the nut cannot be installed and disassembled at all due to the processing error of each nut; 2. After the nut is used for a long time, the nut The card edge will have slack problem, which will affect the use; 3. Installation or disassembly is easy to cause problems such as falling, which may cause electrical short circuit, etc., and there are potential safety hazards; 4. The efficiency of equipment installation is low.
However, due to a radial external tension, the external tension is caused by the tightening axial force generated by the tightening torque, and the phenomenon of open ring expansion occurs, and the spring washer often breaks due to hydrogen embrittlement. The nut exerts uneven pressure on the flat washer through the spring washer. And the friction coefficient between the spring washer and the nut and the flat washer is very small, and the phenomenon of vibration, rotation and relaxation occurs.
In the prior art, spring pads are fixed to the seat pan or to the height adjuster tube. However, in the absence of a seat pan, additional components are required to secure the spring pads to prevent movement of the spring pads in the longitudinal direction of the vehicle. FIG. 1 shows such a seat spring pad 2 , which is fixed to the seat pad 1 by means of additional fixing parts 4 . Additional weight is added due to the use of additional fixing parts and a separate step is required in the assembly process to connect the fixing parts to the spring pads. During use, there may be noise between the spring cushion and the seat cushion
The main categories of screws include ordinary screws, machine screws, self-tapping screws and expansion screws. Cap screws used to be limited to full-thread fasteners. Hex cap screw and Hex bolt Hex bolt As the name suggests, it is a male threaded fastener with a hexagonal head, designed to be turned with a wrench. According to the ASME B18.2.1 standard, the head height and shank length tolerance of the hexagon head screw (Hex cap screw) is smaller than that of the general hex bolt (Hex bolt), so the ASME B18.2.1 hexagon screw is suitable for installation in all hexagon bolts that can be used. places, also including places where the large hex bolts are too large to be used. Socket cap screw (also known as socket head screw or) is a screw with a hexagonal inner hole on the head, which can be tightened or loosened only after a hexagonal ruler (hex key, Allen wrench or Allen key) is inserted into the inner hole. The most commonly used hexagon socket head screws are cylindrical head screws with a head diameter of about 1.5 times the main diameter of the thread (1960 series). Countersunk head cap screw. The counterbore design allows the screw head to rotate without being exposed on the surface of the fixed object, so it is mostly used in places where the surface is small and traditional wrenches are inconvenient to use. Machine screw is generally a screw (4#~12#) with a diameter less than ¼ inches, usually full teeth and rotated by a screwdriver, such as slotted, cross or hexagon socket. Wood screws, machine screws; but can be divided into many categories according to different uses; machine screws can be divided into longitudinal tightening screws and horizontal expansion screws; according to the thread can also be divided into: A: Triangular thread (60 degrees ) : combined/locked/expanded B: triangular thread for pipe (55 degrees): combined/locked 3) C: trapezoidal thread (30 or 29 degrees): power transmission D: square thread (90 degrees): power transmission stainless steel screw Stainless Steel Anti-Drop ScrewsStainless Steel Anti-Drop Screws Machine (Treadmill) Screws And Shafts For Motorcycle Or Bicycle Needle Car Screws, Axes Screws And Shafts For Sewing Macing Socket Set Screws Stainless Steel Wide Thread ScrewsStainless Steel Coarse Thread Screws Stainless Steel High-Low Thread Screws Stainless Steel Machine Screws Stainless Steel Self Drilling Screws Stainless Steel Self Tapping Screws Stainless Steel Self Tapping Screws Stainless Steel Thread Cutting Screws Stainless Steel Triangle Stainless Steel Tri-Lobular Thread Screws Model Description P refers to the head type is PAN head; A refers to the pointed tail teeth, B refers to the flat tail teeth, namely PA round head pointed steel teeth, PB round head flat mouth steel teeth. Self-tapping type: ◆Round head self-tapping screw PA ◆Round head flat tail self-tapping screw PB ◆Round head cutting tail self-tapping screw PT ◆Round head belt self-tapping screw PWA ◆Round head belt and flat tail self-tapping PWB ◆Round head belt Jiecut tail self-tapping PWT ◆Countersunk head self-tapping screw KA ◆Countersunk head flat tail self-tapping screw KB ◆Countersunk head cut-tail self-tapping screw KT ◆Semi-countersunk head self-tapping screw OA ◆Big head self-tapping screw BA ◆Big head flat tail self-tapping screw BB ◆Large flat head self-tapping screw TA ◆Large flat head flat tail self-tapping screw TB ◆Large flat head cutting tail self-tapping screw TT ◆Thin head self-tapping screw CA ◆Thin head flat tail self-tapping screw CB ◆Cup head hexagon socket self-tapping HA ◆Drywall/Wallboard/Fiber Nails Machine Wires: ◆Round Head Machine Screw PM ◆Round Head Machine Screw PWM ◆Large Flat Head Machine Screw TM ◆Countersunk Head Machine Screw KM ◆Half Countersunk Head machine screw OM ◆Large head machine screw BM ◆Thin head machine screw CM ◆Cup head machine screw HM
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: cap nuts, iron nickel-plated cap nuts, open elastic washers, embedded bolts and other products, we can provide you with products suitable for you fastener solutions.
