Service HotlineIn the process of electronic accessories such as mobile phones and computers, especially multi-layer circuit boards, there are generally fixed connections between multi-layer circuit boards or other components. At present, there are two main connection methods. One is to use laser welding. However, the laser welding equipment is expensive and has very high requirements on the position of the weldment. Therefore, during welding, it must be ensured that the final position of the weldment needs to be the same as the laser beam will impact. Solder joint alignment. The other is to use a metal rivet to pass through the positioning hole, and then impact the rivet with a punching needle, so that the open end of the rivet is deformed and opened and pressed on the fixed piece to form a rivet fixed state. However, in actual operation, when the open end of the rivet tube is opened and deformed by the impact, strong cracking often occurs, resulting in a small amount of conductive fracture debris, which falls on the circuit board or other devices to be connected, causing Short circuit, in view of this shortcoming, some manufacturers have changed the metal rivets to plastic materials, but the plastic rivets have poor ductility and often break when impacted with a punching needle, resulting in the failure to achieve the riveting fixing force of the original metal rivets. In addition, the above two fixing methods are complicated in operation and low in installation efficiency.
Guangdong Yueluo Hardware Industry Co., Ltd. provides a nut provided by Yueluo, which includes an internal thread. is an arc curve. Compared with the nut of the same type, the normal pressure and friction force of the nut are increased, the thread is not easy to loosen, and the bolt and nut are in surface contact, so it is not easy to cause stress concentration and local material yield, which effectively improves the tightening force of the bolt and nut. Stability, increase fastening reliability.
The tail of the drill tail screw is in the shape of a drill tail or a pointed tail, and no auxiliary processing is required. Drilling, tapping and locking can be directly carried out on the setting material and basic material, which greatly saves construction time. Compared with ordinary screws, its toughness and pull-out force and maintenance force are high, and it will not loosen for a long time after combination, so it is safe to use. Especially in the combination of construction, construction, residential and other places, self-tapping and self-drilling screws are the best economical fasteners in terms of workability, cost and reliability. Now the construction of high-rise buildings and high-speed traffic in mainland China requires more high-quality drill screws;
An anti-loosening nut structure includes a flat nut and an oblique nut. One end surface of the oblique nut is an oblique surface, and an angle is formed between the oblique surface and the vertical line of the screw hole axis of the oblique nut. Nuts are installed on the bolts one after another, and the mating contact surfaces of the two nuts include the inclined surface, which are tightened in sequence.
Ordinary thread Ordinary coarse thread: Feature code M+ Nominal diameter + Rotation + thread tolerance zone code (pitch diameter, top diameter) - Rotation length Ordinary fine thread: Feature code M+ Nominal diameter * thread pitch + direction of rotation + thread tolerance With code (middle diameter, top diameter) - the length of screwing is omitted for right-handed threads, and the left-handed thread is represented by LH. M 16-5g6g means coarse thread ordinary thread, nominal diameter 16, right-handed, the thread tolerance zone is 5g in the middle diameter and 6g in the major diameter, and the screwing length is considered as the medium length. M16×1 LH-6G means fine thread ordinary thread, nominal diameter 16, pitch 1, left-handed, thread tolerance zone medium diameter and major diameter are both 6G, and the screwing length is considered as medium length. The labeling format is: feature code (cylindrical pipe thread is represented by G, conical pipe thread is represented by NPT) + size code + tolerance grade code + rotation direction G1A--LH represents inch non-threaded sealing pipe thread, size code 1in, left-handed, tolerance The grade is A grade. Rcl/2 means inch thread seal taper pipe thread, size code 1/2in, right-handed.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 4.8 grade white zinc flange nuts, expansion and explosion screws, plastic screws, non-deformation stainless steel and other products, we can provide you with suitable tightening. Firmware Solutions.
