Service HotlineStainless Steel Nut Nut Self-locking Nut, Lock Nut, Lock Nut, Four-jaw Nut, Screw-in Nut Safety Nut, Thin Rod Screw Connection Nut, Self-locking Hexagonal Cap Nut, Special Ground Screw Nut, Hexagonal Crown Thin Nut , Lifting ring nut. [1] Fine pitch all-metal hexagonal flange face locking nut, all-metal hexagonal flange face locking nut, fine pitch non-metallic insert hexagonal flange face locking nut, fine pitch hexagonal flange face nut welding square nut, Welded Hex Nuts, Snap Nuts, Insert Round Nuts
1. For the lock ring of the anti-dropping nut, snap the ring into the lock, tighten the lock claw, and the lock claw is fastened into the thread. The lock claw does not have thread characteristics, and it is difficult for the nut to be threaded during the vibration process of the machine. If it fails, the locking claw acts as a tightening nut, but it does not have the problem of loosening itself like the locking nut.
Traditionally used for plastic fastening screws, most of the thread designs are self-tapping threads, but for different plastic types, the self-tapping threads also have many different classifications, such as PT profile, Plastite series, Remform profile, etc. The structural parameters and manufacturing process of these threads are inconsistent, or require different main molds and wires. Therefore, to find a plastic screw that is universally applicable to various plastic types, has a single pressing structure, low-cost and simple manufacturing process, especially its special self-tapping thread, is an important issue that needs to be solved urgently at present. question. The purpose of Yueluo Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to propose a plastic screw to solve the screw fastening problem that is generally applicable to different plastics. The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to realize a kind of plastic screw through the following technical scheme, it is characterized in that, the thread of the screw is composed of asymmetric threads with a profile angle of 30°, and the threads are The bottom surface of the connection between them is an arc surface. Yueluo preferably, the asymmetrical thread has a forward thread angle greater than the reverse thread angle, and the sum of the two-direction thread angles is 30°. Yueluo further preferred that the tooth profile angle of the asymmetrical screw thread in the forward mounting direction is 20 degrees, and the tooth profile angle in the reverse mounting direction is 14 degrees. Yueluo Guangdong Yueluo Hardware Industry Co., Ltd.'s application of plastic screws, through the improvement of special thread structure, reduces the radial pressure and installation torque when the screw is installed, reduces the damage to the plastic hole; and increases the pull-out resistance of the screw force, it is not easy to appear loose assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
In the design of modern aviation and aerospace vehicles, in order to reduce weight and save space, the space of the fastening installation system is getting narrower and narrower, and blind hole installation is often required. In this case, single-sided riveting installation is usually used for fastening connection. At present, this kind of fastening connection products are mainly blind rivets. The riveting installation principle of blind rivets is to use the method of pulling, pulling the mandrel, and extruding the nail sleeve to deform it at the blind end to achieve the function of fastened connection. This kind of fastening connection method requires special riveting, generally imported riveting, the replacement of internal parts is expensive, the installation process is complicated, and the installation cost is high.
The capped nut can prevent the bolt connection from directly contacting with the outside world, which is corroded and makes it difficult to disassemble later. Nuts with caps in the prior art are mostly of one-piece structure, and the surface is not treated with anti-oxidation, which is easy to be corroded. In addition to the protective effect, the fastening method is the same as that of ordinary nuts, so it is easy to loosen when subjected to severe vibration. .
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: small gear wheel copper nuts, aluminum alloy washers, enlarged square washers, PM round head machine wire screws and other products, we can provide you with suitable products Your fastener solution.
