Service HotlineThe heating bolt pre-stretching method makes the bolt pre-stretch to the required deformation amount by heating, and then tighten the nut. After cooling, the bolt is shortened and the connection is pre-tightened. This is a commonly used fastening method in infrastructure installations. However, it is not suitable for devices that often need to be disassembled and adjusted, because during the disassembly process, the connected parts will be heated and elongated together with the bolts, and the use of open flame heating will be limited in some occasions; the use of electric heating will make the structure of the screw It becomes complicated and increases the investment, and even if it is difficult to disassemble, such as the propeller shaft of the ship, etc., the heating method is not suitable.
In order to achieve the above purpose, Yueluo provides the following technical solutions: threaded rivets include a nail rod, an expansion piece, and a nail sleeve, one end of the nail rod is provided with a mounting piece, and the side of the mounting piece away from the nail rod is movably installed with a mounting piece. There is a driving mechanism. The driving mechanism includes a mounting cylinder and a movable rod. A cross groove is formed at one end of the mounting piece close to the driving mechanism. The rod is movably installed on the inner side of the installation cylinder, and one end of the movable rod close to the cross groove is fixedly provided with a cross connecting piece that matches the cross groove, the cross connecting piece is matched with the cross groove, and the movable rod is far away from the cross groove. One end of the cross connecting piece is fixedly provided with a fixing piece, the fixing piece and the installation cylinder are screwed together by threads, the expansion piece is sleeved on the outer side of the nail rod, and the nail sleeve is movably installed on the nail rod away from the driving mechanism The outer side of one end of the nail rod is movably installed with a fixing mechanism.
The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of the quality also contributes to the improvement of the lifespan of the 7-pack.
The tail of the drill tail screw is in the shape of a drill tail or a pointed tail, and no auxiliary processing is required. Drilling, tapping and locking can be directly carried out on the setting material and basic material, which greatly saves construction time. Compared with ordinary screws, its toughness and pull-out force and maintenance force are high, and it will not loosen for a long time after combination, so it is safe to use. Especially in the combination of construction, construction, residential and other places, self-tapping and self-drilling screws are the best economical fasteners in terms of workability, cost and reliability. Now the construction of high-rise buildings and high-speed traffic in mainland China requires more high-quality drill screws;
Guangdong Yueluo Hardware Industry Co., Ltd. was founded in 1998, and the factory was established in Feilong Industrial Zone, Xiaolan Town, Zhongshan City, Guangdong Province, with an investment of 10 million yuan. The main production is a variety of national standard, non-standard, British, American, metric screws. Mainly include: special screws for the electronics industry (machine screws, self-tapping screws, special screws): nuts (general nuts, flange nuts, external teeth nuts): Washers (external teeth, internal teeth, flat springs) Gaskets, etc.); lathes (precision automatic lathe parts, connecting parts, embedded parts, fasteners, decorative parts, etc.).
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: copper column yin and yang studs, single-pass copper columns, complete sets of accessories, hook expansion bolts and other products, we can provide you with suitable tightening bolts. Firmware Solutions.
