Service HotlineGB bolts are generally divided into two types: GB30 bolts and GB21 bolts. The difference is that the hexagonal head of GB30 is larger than that of GB21. The materials are all used: Q235. The grade is 4.8, the hardness is weak, and it is used for parts with low hardness requirements and infrequent activities, which are called ordinary bolts. The most typical use: machinery, construction, fixing, fastening.
Yueluo relates to a self-tapping screw according to the preamble of claim 1. A self-tapping screw is known from EP0623759B1, the ratio of the outer diameter to the smaller diameter of the self-tapping screw is about 1.25-1.5, the ratio of the outer diameter to the pitch lead is about 1.5-1.6 and the thread The flank angles of , are < 50° and ≥ 35°. EP0433484B1 proposes a self-tapping screw whose thread is provided with cutting teeth of approximately arcuate design, and the cutting edge and the thread crest are at the same horizontal position and are set in opposite directions. One purpose of Yueluo is to realize a general type of self-tapping screw so that it can be screwed particularly easily into holes drilled in concrete or other materials such as bricks and the like. According to Yueluo, this object is achieved by the features in the characterizing part of claim 1, and surprisingly, it has been found that the parallel arrangement of the flanks, ie with a flank angle of about 0°, will make screwing particularly easy when screwing in , especially if the diameter of the hole varies within an allowable tolerance. One reason may be due to the fact that there is no lateral pressure on the material screwed into the thread, even if threads of different depths are cut in concrete or other materials such as brick, chipped plywood, or hardwood. The thread cuts into the material over its entire width by cutting grooves. In particular according to the embodiment of claim 3 the material cut out when screwing in the screw can be discharged without any accumulation, the dependent claims reflecting many advantages of further embodiments.
In order to solve the above technical problems, Yueluo provides a screw installation method. When using this method to install screws, the sensor must sense that the screws have been adjusted to the specified position before allowing the screws to be energized, which prevents the screws from being adjusted. Accidents of personal injury caused by operating errors during the process. The technical solution adopted by Yueluo to solve its technical problems is a screw installation method, which includes the following steps: a. Fix the screw hole structure that needs to be installed on the workbench, and fix the corresponding size screw to the screw mouth; b. Adjust the sensor on the track groove to the vertical position just above the screw hole structure; c. Adjust the screw position until the sensor on the screw senses the signal sent by the sensor; d. Turn on the screw power supply, and install the screw into the screw Inside the hole structure, the installation is complete. Compared with the prior art, Yueluo has the following beneficial effects. The screw installation method provided by Yueluo has the steps of preventing accidental hitting, which avoids personal injury accidents caused by operation errors during the screw adjustment process.
Wire cutters are widely used tools in electromechanical and other industries, and rivets are widely used standard parts, especially in the manufacturing or maintenance process of the electromechanical industry. Because the currently used wire cutters are mostly used to cut finer steel wires or various wires and twist small screws and nuts. In the process of work, rivets of various specifications are often encountered temporarily. For example, suitable rivets cannot be found at the scene, or other replacements will cause inconvenience to the work, which not only affects the output, but also affects the quality.
In the prior art, there are two ways to feed the screws of the locking screw machine, the air blowing type and the air suction type. The air suction type is suitable for relatively small screws. If the screw size is larger than M2, smaller than M5, and the length-diameter ratio is larger than 1.4, the air-blown screw machine can be selected.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: bronze spring washers, six-star bolts, aluminum rivets, cap lock through holes and other products, we can provide you with suitable products for you. Fastener Solutions.
