Service Hotline1. Precautions for the quality of high-strength bolts or screws and flat washers assemblies. The surface of the Phillips hexagon combination screw should be checked for burrs or scratches. There is no oil stains, or rust. To test the material of the combination screw, the strength of the grade used in different high strengths should be consistent with it. Second, the combination bolt and nut should be used together with the same grade as the nut, and the same grade should be used together. Third, when installing and using combined bolts, it should be in reasonable weather conditions and should not be operated in the rain. Fourth, when installing, it is forbidden to use excessive force and excessive force. Lead to sliding teeth, or locking phenomenon.
The retaining ring is divided into two types: shaft use and hole use. Its structural characteristics: The shaft retaining ring is a kind of retaining ring installed on the shaft groove, which is used for positioning and fixing of shaft end parts, and can withstand severe vibration and shock loads, but It is necessary to take anti-loosening measures and installation positioning; the hole is installed in the circular hole with an elastic retaining ring, which is used for the axial movement of the fixed parts. The outer diameter of this retaining ring is slightly larger than the diameter of the assembly circular hole.
In order to achieve the above purpose, Guangdong Yueluo Hardware Industry Co., Ltd. provides the following technical solutions: self-expanding semi-solid installation rivets, used for connecting and perforating two or more units of parts, including top core and rivet body, characterized in that : The top core lock slot opened on the concentric sheath along the longitudinal direction is snapped into and screwed and fixed in the concentric sheath, the top core extends downward into the top core rotary sleeve, the concentric sheath The sleeve is connected with the upper sealing sleeve of the lower body and is connected with the longitudinal axis, a hollow body is arranged below the rivet body, a joint is installed under the hollow body, and a supporting foot is connected to the joint, and the supporting foot and the turning The folding clips are staggered and distributed, the folding clips are concave-convex inclined surfaces, and the supporting feet are slidably connected with the folding clips.
The process of removing iron oxide plate from cold heading steel wire rod is stripping and dephosphorization. There are two methods: mechanical dephosphorization and chemical pickling. Replacing the chemical pickling process of wire rod with mechanical phosphorus removal not only improves productivity, but also reduces environmental pollution. This phosphorus removal process includes bending method (the round wheel with triangular grooves is commonly used to repeatedly bend the wire rod), spray nine method, etc. The phosphorus removal effect is good, but the residual iron and phosphorus cannot be removed (the removal rate of iron oxide scale is 97%) ), especially when the iron oxide scale is very sticky, therefore, mechanical phosphorus removal is affected by iron scale thickness, structure and stress state. Carbon steel wire rods used for low strength fasteners (less than or equal to 6.8) High-strength bolts (greater than or equal to grade 8.8) use wire rods to remove all iron oxide scales after mechanical dephosphorization, and then go through a chemical pickling process for compound dephosphorization. For low carbon steel wire rods, the iron sheets left by mechanical dephosphorization are likely to cause uneven wear of grain draft. When the grain draft hole adheres to the iron sheet when the wire rod rubs against the external temperature, the surface of the wire rod produces longitudinal grain marks. More than 95% are caused by scratches on the surface of the steel wire during the drawing process. Therefore, the mechanical phosphorus removal method is not suitable for high-speed drawing.
spring washer is installed under the nut to prevent the nut from loosening. It is stated in the national standard. Hexagonal slotted nuts are specially designed for use with bolts with holes at the end of the screw, so that the cotter pin can be inserted into the hole of the screw from the groove of the nut to prevent the nut from automatically loosening. It is mainly used for vibration loads or alternating loads. . The methods to prevent the nut (or bolt) from automatically loosening in the mechanical design and production are as follows: 1. Add a spring washer; (simple and easy to do) 2. Use a hexagonal slotted nut + a split pin; (increase the processing process) 3 . Pad the stop washer; (increase the processing process compared with the same period of last year) 4. Insert the steel wire into the hexagon head opening of the hexagon bolt. (Increased processing steps compared to the same period of last year) Spring washers are used to prevent loosening. For example, the bolts connecting the motor and the machine base generally need to add spring washers, because the motor vibrates without the spring washers, and the nuts will loosen. Generally, the fasteners on the equipment with vibration There is a spring gasket on it, and there is generally no need to add a gasket on the flange! Whether the spring gasket is added to the flange is related to the medium circulating in the pipeline. If it is easy to generate pulses, it is best to add spring gaskets, as well as high-speed fluid, and the caliber changes frequently. Do not generalize. On some valves, the stuffing box gland All flanges need to be added with spring gaskets. The automatic selection of spring gaskets is included.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: PVC rigid PVC screws, 8.8 high-strength screw caps, GB96 stainless steel enlarged flat washers, component gaskets and other products, we can provide you with The right fastener solution for you.
