Service HotlineCountersunk head screw, also called countersunk head screw, also known as flat machine screw, is a kind of construction part. The head is a 90-degree cone, similar to common wood screws. The head has tool tightening grooves, such as a zigzag, cross, inner hexagon, plum blossom, pentagon, etc. Screws are all connectors used to connect two objects. Generally, the head of the screw will protrude above the surface of the object to be connected, so that the surface will lose its smoothness. Countersunk head screws can be sunk under the surface to make the surface flat. For hard objects, countersunk holes need to be drilled in the corresponding positions of the countersunk head. In short, the countersunk head is the head of the screw that can keep the surface flat after installation.
The production of stud bolts requires fixed equipment and machine tool processing. Of course, the processing procedure is relatively simple. There are mainly the following procedures: first, the material needs to be pulled out. After this process, the next process can be carried out. The next process is to use a cutting machine to cut the straight and long material into the length required by the customer according to the customer's requirements. This completes the second process. The third process is Put the cut short material on the thread rolling machine and roll out the thread; the ordinary stud bolts are processed here, of course, if other requirements are required, other processes are required. [1] The commonly known bolt refers to the screw with a larger diameter. According to this statement, the diameter of the screw is much smaller than that of the bolt. Stud bolts do not have a head, and some are called studs. Both ends of the stud are threaded, with no thread in the middle and a smooth rod in the middle. Studs are used on large equipment such as gear racks. In actual use, the external load will have vibration and the influence of temperature will reduce the frictional force, and the threaded connection will loosen and fail over time. Therefore, it is necessary to do a good job in the maintenance of the stud bolts at ordinary times. Stud bolts or anchor bolts will have problems under the action of mechanical friction for a long time. When problems occur, the engine oil pan should be removed, and the use of the engine bearing bushes should be carefully checked, and the clearance between the bearing bushes should be checked. Whether it is too large, if the gap is too large, it should be replaced in time. When replacing the stud bolts, also replace the connecting rod bolts. When some large equipment such as nail making machines are in normal operation, if they find that the engine is not running very stable or there is abnormal noise, they should stop and check in time to avoid bigger problems. [1] In each maintenance, the newly replaced stud bolts and other accessories should be inspected. During the inspection, the focus should be on the head and guide part of the stud bolt. Whether there are cracks or dents in each part, and also check whether the tooth shape of the stud bolt has changed. Is there any abnormality in the thread pitch? If there is any abnormality, it must not be used again. A torque wrench should be used when installing the connecting rod cover. It must be tightened according to the specified standards, the torque should not be too large or too small, and attention should be paid to selecting the stud bolts and studs of the supporting manufacturer.
Hexagon nuts are also called hexagon nuts. Generally, there are many types of nuts, such as hexagon nuts, round nuts, square nuts and so on. Some standards for nuts are still relatively clear. Some specifications and size standards, material requirements standards, electroplating standards, etc. are relatively clear. Different types of nuts also have different standards. Let's introduce the specifications and standards of the nuts in detail.
In chemical production equipment, the cylinder body and the head cover need to be connected and sealed. The traditional sealing structure is to connect the two with a screw, add a non-metallic gasket in the middle and fix it with a nut. However, such a sealing structure only controls the tightening torque, and has the technical defect that the sealing ring will be twisted or even broken during repeated loading and unloading of the cylinder head cover, resulting in poor sealing performance.
The rivet provided by Yueluo Creation includes a mandrel and a coaxial matching nail sleeve outside the mandrel; the mandrel includes a head, a central rod and a tail, and a position close to the head is provided with an inner A concave section of the lock ring area, a position close to the tail is provided with a section of lock area that inclines and shrinks inward along the direction of the head to the tail; the lock ring area of the core rod is gap-fitted and fixed with a lock ring , a part of the lock ring is located inside the sleeve head of the nail sleeve, and the part of the lock ring located outside the sleeve head of the nail sleeve can be interference fit with the nail sleeve; the nail sleeve The sleeve is provided with a through hole for the core rod to penetrate into, the inner wall of the nail sleeve forming the through hole is provided with a protruding structure, and one end of the protruding structure is close to the sleeve head of the nail sleeve The end of the core rod is close to or adjacent to the end of the tail of the core rod.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: fine pitch screws, positive national standard washers, set small screws and nuts, hexagon socket flange screws and other products, we can provide you with suitable products for you. Fastener Solutions.
