Service HotlineThe pretreatment process is a key process that determines the quality of nickel-phosphorus plating on high-strength bolts. The purpose of this process is to remove the passivation layer on the surface of the bolt and prevent the regeneration of the passivation film. The execution of this process directly determines the degree of bonding between the substrate and the coating. Most of the quality accidents in production are caused by poor pretreatment of bolts. Before plating, the oil, rust and oxide scale attached to the surface of the bolt must be carefully removed; the difference with electroplating is that it should be inspected more carefully, and plating is absolutely not allowed on unclean bolts. ① Inspection of bolts: Visual inspection of the surface quality of bolts requires that any burrs left by processing must be removed, and sharp edges and corners must be rounded. ② Manual degreasing; ensure that the surface of the substrate is free of oil stains. ③ Soak and remove oil; boil the bolts in alkaline water to remove the surface oil. ④ Pickling: In order to prevent the alkaline degreasing solution from contaminating the flash nickel plating tank, electro-activation treatment is carried out with pickling solution before flash nickel plating. ⑤ Electro-activation; electro-activation treatment with acid solution. ⑥ Flash nickel plating; flash nickel plating should be used for low alloy steel to increase the bonding strength between the coating and the substrate.
Generally speaking, combination screws are widely used in electrical, electric, mechanical, electronic, household appliances, furniture, ships and so on. But the above said that different combination screws have different functions. For example, Phillips pan head combination screws are generally used in small electronic products. Larger cross hexagon combination screws are used in larger electrical products, such as frequency converters, and some larger frequency converters use many cross hexagon combination screws. Hit the inverter case. To loosen the tightening effect. For example, two combination screws with flower teeth, which are used on the inverter, are used to break the paint, so that all the two combination screws on the surface of the casing are powered on. There is also a two-combination screw with a square pressure line, which itself is a two-combination screw with a pan head screw and a square pad. It is generally used on the surface of the terminal block. The function is for wiring and for crimping.
The tooling for screw standard parts provided by Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. mainly solves the problems of low manual operation matching efficiency, wrong specifications of screw standard parts, and easy falling of screw standard parts into the product when assembling screws in the prior art. . The specific technical solutions of Guangdong Yueluo Hardware Industry Co., Ltd. are as follows. The screw standard parts supporting tooling includes a stud sleeve hole plate, a gasket sleeve hole plate and a nut sleeve hole plate with matching structure; the stud sleeve hole plate There is at least one stud hole matching with the assembled stud structure, at least one gasket hole matching with the assembled gasket structure is arranged on the gasket sleeve hole plate, and the nut sleeve hole plate is provided with at least one gasket hole matching with the assembled gasket structure. At least one nut hole matched with the assembled nut structure; the number of stud holes, gasket holes and nut holes are equal. The above-mentioned stud sleeve hole plate is provided with a positioning device, and the gasket sleeve hole plate is provided with a matching positioning hole; or the gasket sleeve hole plate is provided with a positioning device, and the stud sleeve hole plate is provided with a matching positioning hole. The above stud holes are through holes; the nut holes are blind holes. Forty to one hundred and fifty stud holes are arranged on the stud sleeve hole plate. The above-mentioned positioning device is a positioning plate and/or a positioning column. The advantage of Guangdong Yueluo Hardware Industry Co., Ltd. is that the matching tooling for screw standard parts improves the matching quality of screw standard parts, effectively prevents screw standard parts from falling into the product easily and screw specifications are wrong; it simplifies the matching difficulty of screw standard parts and improves assembly efficiency. . The screw standard parts supporting tooling can be processed differently according to different screw standard parts specifications, and the applicability is very wide.
Sprinkle the excess flat washer 6 on the positioning plate II3-1 on the flat washer positioning plate 3, and shake the flat washer positioning plate 3 by hand. After a short time, the flat washer 6 will be positioned and arranged on the upper positioning plate II3-1. In the flat washer hole 3-7, since the width of the opening groove 113-32 of the baffle plate II3-3 is smaller than the diameter of the flat washer hole 3-7, and the thickness of the upper positioning plate II3-1 is designed according to the thickness of the flat washer 6, each Only one flat washer 6 can be accommodated in the flat washer holes 3-7 of each upper positioning plate II3-1, and then use a brush to remove the excess flat washer
ANSI B1.1 Thread Pitch Comparison Table Nominal Diameter (inch〖mm〗) Coarse Thread Pitch (UNC) Fine Thread Pitch (UNF) Ultra Fine Thread Pitch (UNEF) Drilling Diameter (Coarse Thread) Drilling Diameter (Fine Thread) #0 0.060 〖1.524〗 80 1.2 # 1 0.073 〖1.5 1.5 # 2 0.086 〖2.8 # 3 0.099 〖2.515〗 48 56 2.0 2.1 # 4 0.112 〖2.4 # 5 0.125 〖 3.175〗 40 44 2.5 2.6 # 6 0.138 〖3.50〗 32 40 2.7 2.9 # 8 0.164 〖4.166〗 32 36 3.4 3.5 # 10 0.190 〖4.0 # 12 0.216 〖5.486〗 24 28 32 4.5 4.6 1/4 6.35 20 28 32 5.1 5.4 5/16 10.7 11.5 9/16 〖14.288〗 12 18 24 12.3 13.1 5/8 〖15.875〗 11 18 24 13.5 14.7 3/4 〖19.05〗 10 16 20 16.7 17.5 7/8 〖22.125 2.4 9 14 〗 8 12 20 22.2 23.4 The pitch is expressed by the number of teeth per inch, such as: 11 teeth per inch, then the pitch=25.4/11=2.309mm. The unit of pitch in the table is the number of threads per inch. The hole diameter is the recommended hole size for tapping, in millimeters.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: hexagonal copper stud isolation column, fine thread flange nuts, 304316 stainless steel nuts, white zinc square nuts and other products, we can provide you with suitable products for you fastener solutions.
