Service HotlineThe production of stud bolts requires fixed equipment and machine tool processing. Of course, the processing procedure is relatively simple. There are mainly the following procedures: first, the material needs to be pulled out. After this process, the next process can be carried out. The next process is to use a cutting machine to cut the straight and long material into the length required by the customer according to the customer's requirements. This completes the second process. The third process is Put the cut short material on the thread rolling machine and roll out the thread; the ordinary stud bolts are processed here, of course, if other requirements are required, other processes are required. [1] The commonly known bolt refers to the screw with a larger diameter. According to this statement, the diameter of the screw is much smaller than that of the bolt. Stud bolts do not have a head, and some are called studs. Both ends of the stud are threaded, with no thread in the middle and a smooth rod in the middle. Studs are used on large equipment such as gear racks. In actual use, the external load will have vibration and the influence of temperature will reduce the frictional force, and the threaded connection will loosen and fail over time. Therefore, it is necessary to do a good job in the maintenance of the stud bolts at ordinary times. Stud bolts or anchor bolts will have problems under the action of mechanical friction for a long time. When problems occur, the engine oil pan should be removed, and the use of the engine bearing bushes should be carefully checked, and the clearance between the bearing bushes should be checked. Whether it is too large, if the gap is too large, it should be replaced in time. When replacing the stud bolts, also replace the connecting rod bolts. When some large equipment such as nail making machines are in normal operation, if they find that the engine is not running very stable or there is abnormal noise, they should stop and check in time to avoid bigger problems. [1] In each maintenance, the newly replaced stud bolts and other accessories should be inspected. During the inspection, the focus should be on the head and guide part of the stud bolt. Whether there are cracks or dents in each part, and also check whether the tooth shape of the stud bolt has changed. Is there any abnormality in the thread pitch? If there is any abnormality, it must not be used again. A torque wrench should be used when installing the connecting rod cover. It must be tightened according to the specified standards, the torque should not be too large or too small, and attention should be paid to selecting the stud bolts and studs of the supporting manufacturer.
The earless retaining ring for the hole is mostly installed in the annular groove on the inner wall of the pipe fitting. The outer diameter of this kind of retaining ring is slightly larger than the diameter of the assembly round hole. When assembling, the earless retaining ring needs to be pressed into the pipe fitting. Since the inner wall of the pipe fitting is relatively smooth, the earless retaining ring is easily skewed in the pipe fitting. It needs to be adjusted several times before entering the annular groove, and the assembly efficiency is low.
Screw, some people call it screw (screw), screw (screw rod). In fact, the screw is a general term, and the screw and the screw rod are different from each other. Screws are generally called wood screws; they are the ones with a pointed end at the front and a larger pitch. They are generally used to fasten wooden and plastic parts. The screw rod is a machine screw (machine screw), which is the kind of flat head at the front end. The pitch is small and uniform. It is generally used to fasten metal and machine parts.
Guangdong Yueluo Hardware Industry Co., Ltd. discloses a telescopic screw. The main point of its technical solution is that it includes an upper screw rod, one end of the upper screw rod is provided with a screw head, and the other side of the upper screw rod opposite to the screw head is provided with a lower screw rod, and the lower screw rod is provided on the other side. A fixing rod is provided, a limiting hole is set on the fixing rod, a sliding rod is set on the upper screw rod, a limiting block matching the limiting hole is set on the sliding rod, and a cover plate is slidably sleeved on the sliding rod. An inner thread is arranged on the plate, a thread matching the inner thread is arranged on the fixing rod, an elastic member is sleeved on the fixing rod, and both ends of the elastic member are respectively in conflict with the upper screw rod and the lower screw rod. Guangdong Yueluo Hardware Industry Co., Ltd. telescopic screw is provided with a telescopic mechanism between the upper screw and the lower screw. Therefore, the screw can be suitable for threaded installation holes with the same diameter and different lengths, avoiding the screw being limited by the length of the threaded hole and unable to be installed.
The screw rod in the ordinary T-slot nut is cuboid, so the T-slot nut can only be inserted into the nut from the end face of the T-slot, which makes it impossible to quickly complete the installation of the T-nut, which is inconvenient to use. Usefulness is greatly limited.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: heat treatment and hardening, round head positioning pins, top bolts, hexagonal screws with pads and other products, we can provide you with suitable fastening products piece solution.
