Service HotlineMost electrical appliance manufacturers only require the size and riveting gap to be tested for riveted contact components. There is no clear requirement for riveting strength. Only a few manufacturers perform torsion testing on riveting strength. The torque detection method is as follows: use a saw blade to open a one-shaped groove on the rivet head of the riveted contact element, and then insert a torque wrench into the one-shaped open groove to rotate, and measure the torque value. Because most of the electrical contacts are made of copper-silver alloy, the strength is low, and it is easy to slip during the test, and when a saw blade is used to open the one-shaped groove, the width and depth cannot be accurately positioned, so the measured value fluctuates greatly. , has always been an unsolvable technical problem in the industry.
Fasteners are a type of mechanical parts that are used for fastening connections and are widely used. Fasteners are used in a wide range of industries, including energy, electronics, electrical appliances, machinery, chemicals, metallurgy, molds, hydraulics, etc., in various machinery, equipment, vehicles, ships, railways, bridges, buildings, structures, tools, instruments, etc. , chemical industry, instruments and supplies, etc., all kinds of fasteners can be seen, which are the most widely used mechanical basic parts. It is characterized by a wide variety of specifications, different performance uses, and a very high degree of standardization, serialization and generalization. Therefore, some people also refer to a type of fasteners with existing national standards as standard fasteners, or simply as standard parts.
Commonly used screw materials in my country are No. 45 steel, 40Cr, ammoniated steel, 38CrMOAl, superalloy, etc. 1) No. 45 steel is cheap and has good processing performance, but poor wear resistance and corrosion resistance. Heat treatment: quenched and tempered HB220-270, high-frequency quenched HRC45--48. 2) The performance of 40Cr is better than that of No. 45 steel, but it is often plated with a layer of chromium to improve its corrosion resistance and wear resistance. However, the requirements for the chrome plating layer are relatively high. If the plating layer is too thin, it is easy to wear, and if it is too thick, it is easy to peel off. After peeling off, it will accelerate the corrosion, and it has been rarely used. Heat treatment: quenched and tempered HB220—270, hard chrome plated HRC>553) nitrided steel, 38CrMoAl have excellent comprehensive properties and are widely used. Generally, the nitride layer reaches 0.4-0.6 mm. However, this material has low resistance to hydrogen chloride corrosion and is relatively expensive. 4) The superalloy material is superior to other materials. This material does not need coating, and is mainly used for the raw halogen-free screw of injection molding machine. The material has high oxidation resistance and corrosion resistance.
Align the four positioning holes 12-5 of the spring washer positioning plate 2 with the four positioning columns 4 of the screw tray 1, and place them on the screw tray 1. Several screws 5 are passed through the lower positioning plate 12-2 in turn. The spring washer hole 2-7, the opening slot 12-32 of the baffle plate 12-3, the inner ring of the spring washer 7 in the spring washer hole 2-7 of the upper positioning plate 12-1, hold the spring washer positioning plate 2 by hand The raised handle 12-31 of the baffle plate 12-3 pulls the baffle plate 12-3 out of the upper positioning plate 12-1 and the lower positioning plate 12-2, and several spring washers 7 pass through the holes on the lower positioning plate 12-2. The spring washer holes 2-7 fall down along the screw rod of screw 5, so that the screw rod of screw 5 penetrates into the spring washer 7, as shown in Figure 10, and then the spring washer positioning plate 2 is removed to complete the process of threading the spring washer.
The screw and nut disassembly and assembly tool of Yueluo also includes a rotating rod, a sleeve and a fixed rod fixedly connected to the sleeve rod at one end, and the other end of the fixed rod is connected with one end of the rotating rod to make the rotation The rod can be rotated around the connection point, and the sleeve for accommodating nuts or screws is fixedly connected with the other end of the rotating rod; rotating the rotating rod makes the sleeve head and the opening of the sleeve opposite , by keeping the nut or screw in the sleeve fixed while the corresponding screw or nut in the sleeve head rotates, so as to achieve simultaneous force and disassembly of the screw and the nut.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: mechanical bolts, complete sets of external hexagon bolts, flat washers set of external hexagon screws and nuts, external serrated washers and other products, we can provide you with suitable products for you. Fastener Solutions.
