Service HotlineA screw suitable for a variety of tools is a single-structure threaded part, including a screw body and a screw head. The outer surface of the screw body is processed with an external thread 1, and the outer side of the screw head is formed by six screw heads. Prismatic, the top surface of each edge of the outer hexagonal prism is a boss, between each boss is an end face groove 4, and the middle of each boss is provided with an end face hole 3; the inner side of the screw head is formed by six screw heads. The side surface 5 forms an inner hexagonal prism hole, and the bottom of the inner hexagonal prism hole is processed with a cross groove 10 .
Fig. 1, Fig. 2, and Fig. 3 show that the rivet nut is cut into the required blank from a chemically treated low carbon steel disc, and the blank is placed in the die, and the upper and lower punches are used for shaping to obtain a shaped blank. , and then put the shaped blank in the die, use the punch punch to cold-head out the required brim blank (1) and the deformed skirt (2), and then use the punch punch in the die to continue Cold heading out the brim blank (1) and the deformed skirt (2). Then put the semi-finished material into the concave die and use the punch of the punch to continue to squeeze the threaded hole (3) of the nut tapping skirt, and then put the semi-finished blank into the concave die and use the upper punch and the lower sleeve to drop it. material. There are fish teeth (6) below the brim; the outer side of the lower end of the threaded hole is provided with a chamfer (5); the cross-section of the thread of the inner wall of the threaded hole is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave arc (4), In this way, the riveted object is firmly connected to the rivet nut.
1. The taper of the reaming hole should be 90°. It should be guaranteed that it should be less than 90° rather than greater than 90°. This is a key trick. 2. If the thickness of the sheet metal is less than the thickness of the head of the countersunk head screw, you can replace the screw with a smaller size, or it is better to ream a smaller hole instead of reaming the hole to increase the diameter of the bottom hole and cause the parts to not be pressed tightly. 3. If there are multiple countersunk head screw holes on the part, it should be processed more accurately. Once it is drilled crookedly, it will be ugly to assemble, but as long as the error is not large, it can be tightened completely, because when tightening, if the diameter of the screw is not very large. Large (about no more than 8mm), when there is an error in the hole distance, the screw head will be deformed due to the force when it is tightened or it will be tightened.
A rivet is a part that uses its own deformation or interference to connect the riveted parts in riveting. With the continuous progress and development of science, rivets have been used in many occasions because of their convenient use and reliable connection. The rivet includes a nail head and a stem. The traditional processing mold for the rivet head includes a base, and a nail head forming part is arranged on the base. However, due to the limited service life of the mold, the processing mold of this structure is replaced. It needs to be replaced together with the base, which is a waste of material, which increases the production cost, and the rivet itself is relatively cheap, so this reduces the profit of the enterprise.
In view of the above situation, the technical problem to be solved by Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a self-expanding semi-solid installation rivet, the purpose is to solve the existing connection between plastic shells, lightweight plates, insulating materials, circuit boards, or any other In the case of thin, light-weight materials, the grip and bonding force of the rivet itself on the mounting surface is weaker than that of the rivets that are screwed and installed by manual operation. The rivet structure needs to be improved and strengthened when the material is installed.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: knurled shaft cylindrical pins, washer materials, 316L stainless steel washers, small edge ultra-thin flat washers and other products, we can provide you with suitable products Your fastener solution.
