Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a flat gasket that improves the lubrication performance of the contact surface and reduces the friction of the contact surface. Yueluo is implemented through the following technical solutions: a flat gasket with straight upper and lower end faces, characterized in that: the upper and lower end faces are dotted with pits, the pits are spherical pits, and the pit diameter is 2-3mm , the pit depth is between 0.5-lmm. The bottoms of some of the pits are provided with through holes penetrating the upper and lower end faces, and the diameter of the through holes is not greater than 0.5mm. The flat gaskets provided by Yueluo have pits with reasonable design parameters on the upper and lower end faces of the flat gaskets. The pits can store oil, so the lubrication of the contact surfaces of the gaskets can be well improved. It can effectively reduce the friction of the contact surface of the gasket and reduce the failure rate; in addition, the design of the through hole enables a smooth oil passage between the upper and lower end faces of the gasket, ensuring that the upper and lower end faces can be well lubricated.
The circlip lifting and tightening mechanism includes a lifting mechanism and a tightening mechanism; the lifting mechanism includes a lifting cylinder and a ball screw; the output shaft of the lifting cylinder is connected with the ball screw; the ball screw drives the tightening mechanism to achieve up and down move; the tightening mechanism includes a tightening motor, and the output shaft of the tightening motor drives a pinion sleeved on the output shaft to rotate; the pinion drives the largest gear meshed with it to rotate, and the largest gear is driven by The second largest gear meshed with it rotates; the diameter of the first largest gear is the same as that of the second largest gear; the lower ends of the rotating shafts of the first largest gear and the second largest gear are equipped with rotating discs, and each rotating disc is fixedly installed A probe; two probes can be inserted into the two holes of the circlip at the same time, and the circlip can be tightened or loosened as the motor rotates.
The spring washer usually includes a washer body and a raised claw head punched and formed on the washer body. The spring washer is often placed between the bolt head of the bolt and the connected parts, wherein the raised claw head is connected to the part to be connected. The surfaces of the connecting parts are in contact, and the plane on the gasket body, opposite to the lifting direction of the raised claw head, is in contact with the bolt head. After the bolt head is tightened, the elastic reaction force generated by the raised claw head after flattening makes the The screwed threads are pressed tightly, and at the same time, the raised claw head is pressed against the bolt head and the supporting surface of the connected parts, which has the effect of preventing loosening. However, the traditional spring washer is a single-claw type. When tightening, the raised claw head will cause great damage to the surface of the connected parts, so it is not suitable for the anti-loosening treatment of parts with small surface hardness.
Bolts refer specifically to screws with larger diameters and may also have no heads, such as stud bolts. In general, it is not called a stud bolt but a stud stud. The most common form of stud is threaded at both ends and a polished rod in the middle. The most typical use: anchor bolts, or places similar to anchor bolts, thicker connections, when ordinary bolts cannot be used.
screw suitable for a variety of tools is a single-structure threaded part, including a screw body and a screw head. The outer surface of the screw body is processed with an external thread 1, and the outer side of the screw head is formed by six screw heads. Prismatic, the top surface of each edge of the outer hexagonal prism is a boss, between each boss is an end face groove 4, and the middle of each boss is provided with an end face hole 3; the inner side of the screw head is formed by six screw heads. The side surface 5 forms an inner hexagonal prism hole, and the bottom of the inner hexagonal prism hole is processed with a cross groove 12 .
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: color zinc cabinet nuts, four-cornered nuts, high-head knurled screws, Yudongjia 304 stainless steel screws and other products, we can provide you with suitable products for you. Fastener Solutions.
