Service HotlineYueluo Company adopts the following technical solutions: fasteners for preventing nuts from falling off, including bolts and nuts, the nuts are provided with screw holes, the screw holes are provided with internal threads, the bolts are provided with M grooves along its axial direction, M ≥1; There is an arc-shaped notch on the screw hole of the nut, and there are N V-shaped tooth grooves along the axial direction of the nut in the arc-shaped notch, N≥2; a locking strip is placed in the groove, and the locking The bar includes a locking bar body and a V-shaped locking tooth, the width of the locking bar body is the same as the width of the groove, the V-shaped locking tooth is located on one side of the locking bar body, and the V-shaped locking tooth is engaged with the V-shaped locking tooth.
GB6177 Hexagon Flange Nuts - Grade GB55 Hexagon Thick Nuts GB56 Hexagon Extra Thick Nuts GB1229 Large Hexagon Nuts (High Strength for Steel Structure) Lock Nuts Other Names: Root Nuts, Lock Nuts, and Nuts. Purpose: To lock the outer joint of the through wire or other pipe fittings. The working principle of the nut is to use the friction between the nut and the bolt for self-locking. However, the reliability of this self-locking is reduced under dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of the nut locking. Among them, the use of lock nuts is one of the anti-loosening measures.
The front wall sound insulation pad is used to absorb the heat and noise transmitted by the firewall, and also plays the role of heat insulation and vibration isolation, ensuring a relatively quiet and comfortable environment in the car and improving ride comfort. As shown in FIGS. 1 and 2 , the front wall sound insulation and heat insulation pad 101 is generally fixed to the vehicle body by means of screw buckles 102 . The screws 100 are clamped by the clamping feet 103 in the screw The limiting rib 104 clamps the screw 100. After the screw 100 is clamped into the screw buckle 102, the tail end of the screw 100 is exposed, which is easy to scratch the operator when assembling other components, and the exposed screw 100 is easy to cause corrosion, thereby affecting the connection strength of the screw 100, and also The service life of the screw 110 is reduced.
At present, for roller or needle roller bearings without cages, ribs, and low-speed operation, the structure mainly includes inner and outer rings and rollers or needle rollers in the raceway between the inner and outer rings, and additional The retaining rings on both sides of the roller or needle roller, among which the retaining rings added on both sides of the roller or needle roller are annular steel sheets punched from metal sheet, and their function in the bearing is only Correctly guide the rollers or needle rollers to run normally in the raceway between the inner and outer rings to prevent the rollers or needle rollers from deviating and slipping out of the raceway. The defect of the retaining ring of this structure is that first, because the rigid retaining ring and the inner ring are completely separated, there is a gap between the retaining ring and the installation shaft during installation. When the bearing is working, The retaining ring is driven by the outer ring and the rollers or needle rollers to rotate around the installation shaft. Due to the inconsistency of the structure, the retaining ring is easy to fall off during the rotation process, the safety of use is poor, and the rollers or needle rollers will appear toward the raceway. The situation of one side offset, which causes the bearing load center to offset, affects the reliability of the bearing operation, and ultimately affects the service life of the bearing; There is a gap between the raceways of the needle, so the tidbits, dust, etc. generated during the working process will continue to enter the raceway between the inner and outer rings. It is stuck; in addition, due to the gap between the steel retaining ring and the raceway, the grease stored in the raceway will be continuously lost, which will cause the bearing to heat up due to frequent lack of grease, or even burn out, which also affects the to the service life of the bearing.
Bolts with low hardness and strength. Generally, ordinary bolt materials are produced with ordinary screw wires. The hardness, strength, tensile strength and torsion force of ordinary bolt materials are not very high. High-strength bolts generally refer to high-strength bolts. Its own screw material, bolt material, and bolt material are relatively good, and the hardness is relatively high, and after the production is completed, the bolts will be hardened. Make the bolts meet the grade strength requirements of high-strength bolts.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: decorative rivets, hand percussion rivets, black aluminum countersunk head rivets, C-class extra large washers, cage nuts and other products, we We can provide you with the right fastener solution for you.
