Service HotlineA screw suitable for a variety of tools is a single-structure threaded part, including a screw body and a screw head. The outer surface of the screw body is processed with an external thread 1, and the outer side of the screw head is formed by six screw heads. Prismatic, the top surface of each edge of the outer hexagonal prism is a boss, between each boss is an end face groove 4, and the middle of each boss is provided with an end face hole 3; the inner side of the screw head is formed by six screw heads. The side surface 5 forms an inner hexagonal prism hole, and the bottom of the inner hexagonal prism hole is processed with a cross groove 10 .
Subject content and scope of application This technical requirement specifies the technical requirements for the manufacture, installation and inspection of high-strength bolted joints of mobile machinery and equipment. Contents not specified in this technical requirement shall be implemented in accordance with relevant national standards. This technical requirement applies to mobile machinery steel structures that require high-strength bolted connections. This technical requirement applies to quality control and construction methods for in-plant and on-site installations. 2. Joint surface treatment 2.1 For friction type high-strength bolt connections, the joint surfaces at the joints are required to be in close contact with each other and have a sufficient friction coefficient. When the design drawing does not specify the treatment requirements for the joint surface, the treatment shall be carried out according to the following regulations: sandblasting or shot blasting the joint surface of high-strength bolts, remove impurities such as rust and oil stains on the surface, and reach the Sa2.5 standard , the roughness is 50 ~ 75μm, and the friction coefficient shall not be lower than 0.40. When there are regulations in the drawings, follow the regulations in the drawings. 2.2 The friction surface of the treated high-strength bolt connection should take protective measures to prevent contamination with dirt and oil. It is strictly forbidden to make any marks on the friction surface of the high-strength bolt connection. During storage in the factory, or during transportation, to the installation site, special precautions should be taken to prevent contamination of the connection surfaces. The installation unit should pay special attention to protecting the cleanliness and friction surface characteristics of the connecting plate of the high-strength bolt and the connecting surface of the parent body. It is not allowed to use a grinder to grind the connecting surface of the connecting plate and the connecting surface of the parent body. 3 Inspection of the anti-slip coefficient of the friction surface of high-strength bolts The inspection of the anti-slip coefficient should be based on the steel structure manufacturing batch, and each 2000t of a single project is regarded as a manufacturing batch, and those less than 2000t are regarded as a batch. When two or more surface treatment processes are selected, each surface treatment process needs to be inspected. Each batch of three groups of specimens. If the connection is diffused to an external enterprise, each corresponding enterprise shall conduct an anti-slip coefficient test. 3.1 The test piece used for the anti-slip coefficient test should be processed by the factory or the diffusion enterprise. The test piece and the representative steel structure member should be of the same material, produced in the same batch, using the same friction surface treatment process and have the same surface state. And use the same batch of high-strength bolt connection pairs of the same performance level and store them under the same environmental conditions. The anti-slip coefficient test is carried out according to the test method of GB50205 Code for Acceptance of Construction Quality of Steel Structure Engineering. 3.2 The minimum value of the anti-slip coefficient inspection must be equal to or greater than the design specified value. When the above specified values are not met, the friction surface of the component should be reprocessed. The friction surface of the treated component is re-inspected. 4. Connection and installation of friction type high-strength bolts for steel structures 4.1 Preparations before installation 4.2 Select qualified bolts, nuts and washers. The guarantee period for the torque coefficient of the connecting pair is six months from the date of delivery. 4.3 Bolts, nuts and washers in the following cases are unqualified products and are prohibited from being used. a. The source (manufacturer) is unknown; b. The mechanical properties are unknown; c. The torque coefficient k is unknown; d. Defective; e. No performance test report attached; f. Mixed with other batches of bolts; g. Bolts with insufficient length, that is, the bolt head does not show the end face of the nut after tightening. Generally, the length of the end face of the nut to be taken out is 2 to 3 threads. h. The torque coefficient of the connecting pair exceeds the warranty period. Special attention should be paid to waterproofing during transportation and storage. 4.4 Before the construction of the large hexagonal head high-strength bolts, the torque coefficient of the high-strength bolt connection pair should be re-inspected according to the factory approval. Each batch of 8 sets should be re-inspected. Less than or equal to 0.010. The re-inspection method of the torque coefficient shall be carried out in accordance with the provisions of GB50205 Code for Acceptance of Construction Quality of Steel Structure Engineering. The installation of high-strength bolts should be carried out within a short period of time after the test.
The head of the traditional screw is located outside the threaded hole and occupies a large space, which is not suitable for occasions with small space, nor is it suitable for occasions where the outer surface of the component is a working surface. For example, in the field of electronic products, or when connecting the shaft and the shaft sleeve, the machine screw with a fully threaded structure on the outer surface is widely used.
The rivet provided by Yueluo Creation includes a mandrel and a coaxial matching nail sleeve outside the mandrel; the mandrel includes a head, a central rod and a tail, and a position close to the head is provided with an inner A concave section of the lock ring area, a position close to the tail is provided with a section of lock area that inclines and shrinks inward along the direction of the head to the tail; the lock ring area of the core rod is gap-fitted and fixed with a lock ring , a part of the lock ring is located inside the sleeve head of the nail sleeve, and the part of the lock ring located outside the sleeve head of the nail sleeve can be interference fit with the nail sleeve; the nail sleeve The sleeve is provided with a through hole for the core rod to penetrate into, the inner wall of the nail sleeve forming the through hole is provided with a protruding structure, and one end of the protruding structure is close to the sleeve head of the nail sleeve The end of the core rod is close to or adjacent to the end of the tail of the core rod.
rivet with a simple structure includes a rivet cap, a rivet main rod, a rivet limit rod and a limit hole. The rivet main rod is provided with a limit hole inside, the rivet limit rod is located below the rivet main rod, the upper end side of the rivet limit rod is provided with a limit groove, the limit groove is connected with the lower end of the rivet main rod, and the groove surface of the limit groove is round. arc-shaped, the lower end side of the rivet limit rod is provided with four limit grooves, the cross section of the limit groove is in the shape of a right-angled trapezoid, the limit hole passes through the interior of the rivet limit rod and the rivet main rod, and one end of the limit hole The hole surface and the lower end surface of the rivet limit rod are on the same plane.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: multi-type carbon steel nuts, one flat and one spring Phillips screw, cotter pin, large brim closed rivet and other products, we can provide you with suitable products for you fastener solutions.
