Service HotlineA nut provided by Yueluo. The nut is in the shape of a casing and is provided with a threaded section. One end of the threaded section is provided with a protrusion on the wall of the hole. The nominal size of the segment or the distance from the rear end of the lug to the hole core in the screw-in direction is smaller than the nominal size of the threaded segment.
Traditionally used for plastic fastening screws, most of the thread designs are self-tapping threads, but for different plastic types, the self-tapping threads also have many different classifications, such as PT profile, Plastite series, Remform profile, etc. The structural parameters and manufacturing process of these threads are inconsistent, or require different main molds and wires. Therefore, to find a plastic screw that is universally applicable to various plastic types, has a single pressing structure, low-cost and simple manufacturing process, especially its special self-tapping thread, is an important issue that needs to be solved urgently at present. question. The purpose of Yueluo Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to propose a plastic screw to solve the screw fastening problem that is generally applicable to different plastics. The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to realize a kind of plastic screw through the following technical scheme, it is characterized in that, the thread of the screw is composed of asymmetric threads with a profile angle of 30°, and the threads are The bottom surface of the connection between them is an arc surface. Yueluo preferably, the asymmetrical thread has a forward thread angle greater than the reverse thread angle, and the sum of the two-direction thread angles is 30°. Yueluo further preferred that the tooth profile angle of the asymmetrical thread is 20 degrees in the direction of installation, and the tooth profile angle in the reverse direction is 12 degrees. Yueluo Guangdong Yueluo Hardware Industry Co., Ltd.'s application of plastic screws, through the improvement of special thread structure, reduces the radial pressure and installation torque when the screw is installed, reduces the damage to the plastic hole; and increases the pull-out resistance of the screw force, it is not easy to appear loose assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
Nuts are used as fasteners, and most of them need to be used in conjunction with gaskets in the process of use to adjust the deficiencies of the material itself and strengthen the degree of tightening, while metal materials are used as raw materials for gaskets. The cost is also relatively high, and in the process of use, the end face of the metal gasket and the nut will also be affected by the process, resulting in the defect that the fastening effect is not firm and easy to loosen.
The core rivet is another type of single-sided riveting. When riveting, the head of the rivet is hit with a hammer to expose the core, so that it is flush with the end face of the nail head, that is, the riveting operation is completed, which is very convenient, especially suitable for inconvenient Riveting occasions using ordinary rivets (which must be riveted from both sides) or blind rivets (lack of a rivet gun). Usually use flat head rivets, countersunk head rivets are suitable for occasions where smooth riveting is required on the surface.
Large, countersunk, and thin rivet nuts can be produced according to different die angles. Then the cold forged rivet nut is degreasing, cleaned and annealed, and then extruded and tapped and surface electroplated. Since the rivet nut is formed by cold extrusion of low carbon steel, it has high mechanical properties. Specifically, the tensile strength of M3 is 250Kg, the shear strength is 140Kg; the tensile strength of M4 is 700Kg, the shear strength is 220Kg; the tensile strength of M5 1100Kg, shear force 380Kg; M6 tensile force 1750Kg, shear force 450Kg; M8 tensile force 2650Kg, shear force 660Kg.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: polishing and hardening, fastener spring opening washers, flat head screws, 304 lock nuts and other products, we can provide you with suitable products Your fastener solution.
