Service HotlineAs one of the indispensable parts in automobiles, the main function of the screw is to fix the parts with through holes and the parts with screw holes together. The existing automobile screws include a screw rod and a head, and the thread pitches on the screw rod are equal. , When in use, directly screw the screw into the screw hole, so as to connect and fix the two parts, this connection method, however, when the screw has different thread spacing or part of the thread is damaged, the thread cannot be repaired and replaced. Then the whole screw will be scrapped.
The pull-out type positioning pin and the tie-suspended type positioning pin are in the form of a straight cylindrical shape. The pull-out locating pin is temporarily pulled out from the connected piece of the tooling, and it is in a loose state; the tail of the tie-suspended locating pin is connected with a tie such as iron wire or string to the connecting piece of the tooling. After the locating pin is pulled out, the tie Suspended on tooling. The main disadvantages of the two types of positioning pins are as follows: First, the suspension straps are easy to fall off after long-term wear, and the pull-out positioning pins of the same parts are not convenient for on-site storage and placement, and are usually placed on the nearby ground at will; All kinds of positioning pins are prone to position transfer, forgetting and losing, which affects the reset of the tooling and the subsequent manufacture and assembly of aircraft products.
Fig. 1, Fig. 2, and Fig. 3 show that the rivet nut is cut into the required blank from a chemically treated low carbon steel disc, and the blank is placed in the die, and the upper and lower punches are used for shaping to obtain a shaped blank. , and then put the shaped blank in the die, use the punch punch to cold-head out the required brim blank (1) and the deformed skirt (2), and then use the punch punch in the die to continue Cold heading out the brim blank (1) and the deformed skirt (2). Then put the semi-finished material into the concave die and use the punch of the punch to continue to squeeze the threaded hole (3) of the nut tapping skirt, and then put the semi-finished blank into the concave die and use the upper punch and the lower sleeve to drop it. material. There are fish teeth (6) below the brim; the outer side of the lower end of the threaded hole is provided with a chamfer (5); the cross-section of the thread of the inner wall of the threaded hole is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave arc (4), In this way, the riveted object is firmly connected to the rivet nut.
The technical solution of Guangdong Yueluo Hardware Industry Co., Ltd. is: Guangdong Yueluo Hardware Industry Co., Ltd. discloses an anti-dropping nut, which includes a lock, a lock plate, a nut body, a lock ring and a lock claw. The lock ring and the nut body When used together, the lock ring is a circular ring, the inner diameter of the lock ring is larger than the inner diameter of the circumscribed circle of the nut body, the outer diameter of the lock ring is smaller than the inner diameter of the lock buckle, the lock disk is an arc-shaped metal plate, and the number of lock disks is greater than or equal to three. One short side end of the lock plate is connected to the nut body, and the other end of the lock plate is connected to the lock pawl, the lock plate is inclined to the outside of the nut body, and the lock catch is arranged on the outer side of the connection end between the lock pawl and the lock plate. On the side, the lock is a concave arc.
Specification label broadcast representation format: Thread specification d=M12, nominal length L=80mm, and performance level 4.8 equal-length stud bolts are completely marked as: GB 901 M12×80 [1] Product example: Stud studs are generally required After surface treatment, there are many types of bolt surface treatment, commonly used are electroplating, blackening, oxidation, phosphating, electroless zinc flake coating treatment, etc. However, electroplated fasteners account for a large proportion of the actual use of fasteners. Especially in automobiles, tractors, home appliances, instrumentation, aerospace, communications and other industries and fields are more widely used. However, for threaded fasteners, not only a certain anti-corrosion capability is required in use, but also the interchangeability of threads must be ensured, which can also be called screwability here. In order to meet the dual-use performance of anti-corrosion and interchangeability required by threaded fasteners in use, it is very necessary to formulate special plating standards.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: enlarged flat washers, cap-shaped decorative caps, round ball head caps, flat-exploded screws, GB955 and other products, we can provide you with suitable screws for you. Firmware Solutions.
