Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a new type of open blind rivet suitable for riveting of aluminum Al, steel St, and stainless steel SST sheets with foam material in the middle. The new rivet improves the mandrel process, adopts aluminum mandrel, the head of the mandrel has a pit for easy deformation, and there is a conical stop groove above the breakpoint of the mandrel. The mandrel can be caught by the stopper to prevent the nail head from being exposed. At the same time, lock the core rod not to loosen.
The production of non-standard round flat pads can only be processed on ordinary lathes without punching machines. Processing with round steel is difficult, material waste is large, tool loss is large, and efficiency is low. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a non-standard circular flat pad lathe processing fixture, which is suitable for the production of various non-standard circular flat pads. Yueluo is realized in this way. It includes a hollow square support, a bolt and a circular machining groove. It is characterized in that a circular machining groove is left on one surface of the hollow square support. There are 4 bolts evenly connected. The advantages of Yueluo are: 1. Reduce the difficulty of processing; 2. Save materials (can use corner waste); 3. Reduce tool wear; 4. Improve production efficiency.
An asphalt pavement screw, the asphalt pavement screw includes a main rod, an outer jacket, a pressing piece and a nut, the main rod is a columnar rod, the lower end of the main rod is provided with a table for supporting the outer jacket, and the middle part of the main rod passes through the outer jacket The upper part of the main rod is provided with a threaded section, the pressing piece and the nut are set on the threaded section, and at least two deformation holes are provided on the outer sleeve, and the middle part of the deformation hole is larger than the upper and lower sides of the deformation hole, The part between the adjacent deformation holes is the deformation part, and the width of the middle part of the deformation part is smaller than the width of the upper and lower sides of the deformation part. After the asphalt pavement screw of Guangdong Yueluo Hardware Industry Co., Ltd. is assembled, it has strong bonding force with the asphalt road. Even if it is hit, it will not be separated from the asphalt road. Using this asphalt pavement screw to fix the road railing can strengthen the road railing. The firmness of the assembly.
1. The twisted screw should be considered according to the actual inner diameter of the barrel, and the outer diameter deviation of the new screw should be given according to the normal clearance with the barrel. 2. After the thread surface with the reduced diameter of the worn screw is treated, the wear-resistant tungsten carbide alloy is thermally sprayed, and then ground to size. 3. Surfacing wear-resistant tungsten carbide alloy on the thread part of the worn screw. According to the degree of screw wear, surfacing welding is 1~2mm thick, and then the screw is ground and processed to size. This wear-resistant tungsten carbide alloy is composed of materials such as C, Cr, Vi, Co, W and B, which increases the wear resistance and corrosion resistance of the screw. 4. The bottom diameter of the screw is repaired by electroplating hard chromium. Chromium is also a wear-resistant and corrosion-resistant metal, but the hard chromium layer is easier to fall off.
One of the steps in the screw production and processing process is to slot the screw head to facilitate the use of a screwdriver when tightening or loosening the screw. Generally, companies use manual sorting, and then use the cutting knife to slot the front end screws through the track, which is inefficient, and because the screws are not fixed, the cutting knife may easily fly out or break the blade during cutting. It is a safety problem, and after cutting, the screw head has rough workmanship and burrs, which is easy to hurt the hand.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: O-bolts, carbon steel blackened gaskets, hardware precision hand-tightened nuts, high-foot wide-brimmed eyelets and other products, we can provide you with The right fastener solution for you.
