Service HotlineCombination bolts refer to a bolt with a spring washer and a flat washer, which are combined by rubbing teeth. Before the combination bolt is used, the bolt, the spring washer and the flat washer are generally combined by a specific machine. The combined production line mainly includes the processes of feeding, discharging, feeding, charging, screwing and tightening. The existing combined bolt production equipment mainly transmits the bolts to each process through the conveyor belt, and finally completes the combined assembly. The machines in each process are scattered and the space is occupied. The vibrating plate feeding generally puts the bolt head up, and its bolts, spring washers, etc. After the flat pad is assembled, the fixation is poor, and it is easy to fall off during the assembly process.
The flat key is simple in manufacture, reliable in operation, convenient in assembly and disassembly, and widely used. The flat key transmits torque by contacting the two sides of the keyway with the two sides, that is, the side is the working surface, so the main technical requirements for assembly are: to ensure the matching requirements between the flat key and the keyway of the parts on the shaft, and to transmit the movement smoothly and torque. The matching nature of the key and the keyway generally depends on the working requirements of the mechanism. The key can be fixed on the shaft or the hub, and can slide relative to another matching part (guide flat key); it can also be fixed on the shaft and the hub at the same time (ordinary flat key), and based on the size of the key, by changing the shaft The size of keyway and hub keyway can meet different matching requirements.
Pins are widely used. In the connection of the rotating mechanism of two moving components, such as the crank mechanism, the turning mechanism, the connection between the hydraulic cylinder and the moving parts, the pins are used. kind. In order to ensure the normal use of the running equipment and prevent the cylindrical pin from slipping out and falling off during use, some anti-falling methods are usually used at the head of the pin, such as 1. Drill holes and insert cotter pins to prevent the pins from slipping out; 2. The external thread is tightened with a nut to prevent the pin from slipping out; 3. The slot is clamped with a circlip to prevent it from slipping out, etc. These measures make the cylindrical pin very practical in the case of infrequent disassembly and assembly, but in the actual use of the field, in order to prevent the collision of some equipment during each troubleshooting or maintenance, the pin needs to be pulled out and turned up, etc. After the failure or maintenance is completed, put down and then insert the pin to restore, this process will bring trouble to the actual operator. For example, special tools must be brought with you every time you disassemble and assemble the pin, and the split pin or the circlip is easily damaged after repeated disassembly and assembly. , In order to save trouble, the operator sometimes uses iron wire to thread or fasten it instead, and even does not remove the pin for the sake of speed and convenience, which is easy to cause damage to the equipment when dealing with faults.
Screws are a common fastener widely used in machinery, electrical appliances and buildings. The general material is metal or plastic, it is cylindrical, and the grooves engraved on the surface are called threads. Due to the different units of measurement, the representation methods of various threads are also different. For example, M16-2X60 represents a metric thread. His specific meaning is that the nominal diameter of the screw is 16MM, the pitch is 2MM, and the length is 60MM. Another example: 1/4—20X3/4 means the inch thread, what he specifically means is the nominal diameter of the screw It is 1/4 inch (one inch = 25.4MM), there are 20 teeth on one inch, and the length is 3/4 inch. In addition, if you want to express American screws, UNC and UNF are usually added to the back of the British screws to distinguish between American coarse teeth or American fine teeth.
Among them, the pneumatic riveting machine is more commonly used. The pneumatic riveting machine is also equipped with a clamp for assembling the rivet. The existing clamp usually uses two rotating clamps for fastening and assembly, but the rotation easily causes the two clamps to buckle. Misalignment, thus affecting the assembly of the rivet.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: round head round cup screws, 8-level black flat washers, wall screws and nuts, plastic screw caps and other products, we can provide you with suitable products for you fastener solutions.
