Service HotlineThe purpose of Yueluo is to provide a brake pad rivet with shrinkage that can not only solve the problem of normal feeding during assembly, but also save the processing cost of the original machining chamfering and reduce the quality risk of the rivet in use. its production method.
rivet assembly device is provided with a base, the middle of the base is provided with a vertical groove, the bottom wall of the vertical groove extends forward and a horizontal convex block is suspended; the top surface of the convex block is fixed with a vertical rivet Needle and a guide column, the column body of the guide column is covered with a return spring; a downwardly open sliding block is mounted on the convex block, and the upper ends of the rivet needle and the guide column respectively protrude into the sliding block on the top wall of the sliding block. In the riveting pin hole and the guide hole, the inner wall of the riveting pin hole is provided with a large upper and a lower small horizontal step; the upper part of the bottom wall of the vertical groove is provided with a guiding limit rib. Guangdong Yueluo Hardware Industrial Co., Ltd. sets the rivet needle under the workpiece, and uses the upper die punch to press down the workpiece, and the rivet needle completes the operation of the rivet, omitting the operator to turn over and carry the rivet terminal board, thus effectively avoiding the rivet from The phenomenon that the rivet hole comes out. In addition, during operation, the workpiece is placed on the top surface of the slider, and the workpiece guide limit ribs and guide columns are used as shafts and radial limiters respectively. The riveting quality is good, and the purpose of saving time and labor and high efficiency is achieved.
Semi-round head plastic screws have high-quality characteristics such as insulation, non-magnetic, corrosion resistance, beautiful appearance, and never rust, and modified engineering plastics, its strength and impact resistance are comparable to those of metals. The plastic screws we often say are commonly known as nylon. After adding 30% glass fiber to the screw, its mechanical properties are far superior to ordinary nylon. The materials used for the dome head plastic screws are becoming more and more diverse, the performance is constantly improving, and the application fields are becoming wider and wider. 1. Medical equipment industry (insulation, non-magnetic, environmental protection, anti-interference, make medical equipment safer to use) 2. Wind power industry (isolation and insulation of chassis circuit PCB boards) 3. Aerospace industry (electronic equipment Insulation, anti-interference) 4. Office equipment industry (never rust, beautiful and practical) 5. Petrochemical industry (high temperature resistance, chemical resistance, corrosion resistance, prolong equipment life) 6. Electronics industry (insulation, anti-interference) , light weight) 7. Communication industry (insulation, non-magnetic, safety) 8. Ship industry (acid resistance, alkali resistance, corrosion resistance, extended service life), etc... .
Bolts made of high-strength steel, or bolts that require a large pre-tightening force, can be called high-strength bolts. High-strength bolts are mostly used for the connection of bridges, rails, high-voltage and ultra-high-voltage equipment. The fracture of this kind of bolt is mostly brittle fracture. High-strength bolts applied to ultra-high pressure equipment need to be prestressed to ensure the sealing of the container.
hand screw is a screw with a plastic head, and the user fixes the hand screw by turning the plastic head by hand. At present, a hand screw is disclosed in the market publication number CN202203253U, which includes a plastic head and a screw rod, the plastic head and the screw rod are connected together, and the height of the plastic head is higher than that of an ordinary screw, and the height is 12 cm. The screw of the hand screw is fixed in the plastic head by glue. After a period of use, the aging of the glue leads to the loosening of the screw and the plastic head. When the plastic head is stressed, the screw rod comes out of the plastic head, which affects the normal use of the hand screw.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: concave head external hexagon bolts, H59 injection molded copper nuts, internal thread straight nuts, round head positioning pins and other products, we can provide you with suitable products for you. Fastener Solutions.
