Service Hotlinerivet automatic feeding device comprises a feeding installation frame, the upper end of the feeding installation frame is provided with a horizontally arranged receiving block mounting plate, the upper surface of the receiving block installation plate is provided with a rivet receiving block, a rivet The upper surface of the receiving block is provided with a receiving block movable groove that opens upward and completely penetrates left and right. The left movable receiving rod can be embedded in the receiving block movable groove relatively movably, and the right movable receiving rod is located on the right end side of the left movable receiving rod. The receiving rod, the right end of the left movable receiving rod is provided with a left receiving groove that opens upward, and the left end of the right movable receiving block is provided with a right receiving groove that opens upward;
When the countersunk head screws and hexagon socket head bolts are produced by the cold heading process, the original structure of the steel will directly affect the forming ability of the cold heading process. In the process of cold heading, the plastic deformation of the local area can reach 60%-80%, so the steel must have good plasticity. When the chemical composition of the steel is constant, the metallographic structure is the key factor to determine the plasticity. It is generally believed that the coarse flaky pearlite is not conducive to cold heading forming, while the fine spherical pearlite can significantly improve the plastic deformation ability of the steel. For medium carbon steel and medium carbon alloy steel with a large amount of high-strength bolts, spheroidizing (softening) annealing is performed before cold heading, so as to obtain uniform and fine spheroidized pearlite to better meet the actual production needs. For the softening annealing of medium carbon steel wire rods, the heating temperature should be kept above and below the critical point of the steel, and the heating temperature should not be too high, otherwise tertiary cementite will precipitate along the grain boundary, resulting in cold heading cracking. The wire rod of medium carbon alloy steel is annealed by isothermal spheroidization. After heating at AC1+ (20-30%), the furnace is cooled to slightly lower than Ar1, the temperature is about 700 degrees Celsius for an isothermal period, and then the furnace is cooled to about 500 degrees Celsius and air-cooled. The metallographic structure of the steel changes from coarse to fine, from flake to spherical, and the cracking rate of cold heading will be greatly reduced. The general area of softening annealing temperature for 35\45\ML35\SWRCH35K steel is 715-735 degrees Celsius; while the general heating temperature for spheroidizing annealing of SCM435\40Cr\SCR435 steel is 740-770 degrees Celsius, and the isothermal temperature is 680-700 degrees Celsius.
Fasteners are a class of mechanical parts that are used for fastening connections and are widely used. It is used in a wide range of industries, including energy, electronics, electrical appliances, machinery, chemical industry, metallurgy, mold, hydraulic and other industries, in various machinery, equipment, vehicles, ships, railways, bridges, buildings, structures, tools, instruments, chemicals, instruments And supplies, etc., you can see all kinds of fasteners, which are widely used mechanical basic parts. In the fields of listed rails, construction machinery, etc., due to the harsh application environment, the requirements for fasteners are more stringent. If the fasteners are loosened, it may lead to serious consequences, resulting in a large amount of property damage, even serious life cost.
Rivets are nail-shaped objects with a cap on one end: in riveting, the riveted parts are connected by their own deformation or interference. There are many types of rivets, and they are not restricted in form. Commonly used are R-type rivets, fan rivets, blind rivets, tree-shaped rivets Rivets, semi-circular head, flat head, semi-hollow rivets, solid rivets, countersunk head rivets, blind rivets, hollow rivets, these usually use their own deformation to connect the riveted parts, generally less than 8 mm with cold rivets, larger than this size with Hot riveting, but there are exceptions. For example, the nameplate on some locks is riveted by the interference between the rivet and the lock body hole. The rivet pliers are used to cut rivets. The existing rivet pliers have a simple structure and cannot be riveted according to the The user needs to cut a certain length of rivets, and cutting the rivets is time-consuming and labor-intensive, and it is not convenient for people to use.
Usually, a tight fit is used between the cylindrical pin and the pin hole, such as the cooperation between the cylindrical pin and the pin hole on the rotating shaft of the motor. Due to the tight fitting structure between the cylindrical pin and the pin hole, the shaft with the pin hole needs to be well positioned during assembly, and then the cylindrical pin is aligned with the pin hole, and then knocked or pressed to fit. The cylindrical pin is pressed into the pin hole. There is no device specially used for the installation of cylindrical pins in the prior art, and two or more people are required to cooperate to install the cylindrical pins into the pin holes. installation quality.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 201 stainless steel nylon lock nuts, carbon steel plated screws, complete specifications, set nuts and other products, we can provide you with suitable tightening. piece solution.
