Service HotlineLock washers feature easy installation. 1. Just place the helical tooth surfaces on the inner side of the two washers against each other and place them between the nut and the connecting material; 2. After the nut is tightened, the radially convex surface on the outer side of the lock washer and the contact surfaces at both ends are in an engaged state, and The angle of the slope angle of the helical tooth surface on the inner side of the washer is greater than the thread angle of the bolt; 3. When the bolt is elongated due to mechanical vibration, the nut will rotate and loosen accordingly. Because the frictional force of the outer radial convex surface of the lock washer is greater than the frictional force between the inner helical tooth surfaces. In this state, only the relative dislocation between the inner helical tooth surfaces is allowed to generate a certain lifting tension; 4. When the bolt shrinks, the helical tooth surface of the washer will make the nut return to its original position. So as to achieve 100% anti-loose and tightening effect; 5. Washers are suitable for relatively flat and smooth surfaces; 6. If the connecting material is non-metallic material, a metal plate can be fixed on the connecting material, so that the Use the lock washer; 7. There is no need to use a torque wrench when installing the lock washer; 8. You can choose to use an air tool when installing or removing the lock washer.
Heat resistance refers to both the oxidation resistance or gas medium corrosion resistance at high temperature, that is, thermal stability, and at the same time, it has sufficient strength at high temperature, that is, thermal strength. As the material requirements of products produced by customers are getting higher and higher, the requirements for screws used in product materials are also getting higher and higher. When product materials face harsh environments and special occasions, more and more high-quality mechanical properties of stainless steel screws are used. Therefore, stainless steel screws were selected. The requirements are getting higher and higher, and the material of stainless steel screws is getting higher and higher. Therefore, many ordinary stainless steel screws SUS201 are replaced by stainless steel SUS304 screws and stainless steel screws SUS316. Of course, if some requirements are not so high, general customers will choose stainless steel screws SUS201, which are relatively cheap in cost.
R-type plastic rivets, also known as expansion rivets, are composed of plastic sub-nails and female buckles. It is not necessary to use installation tools during installation, place the installation base in the smooth hole, and then press the head, the specially designed feet expand and stretch after being stressed, and are firmly locked on the installation surface. It is often used to connect plastic shells, lightweight boards, insulating materials, circuit boards, or any other thin, light-weight materials. It is beautiful, practical, and easy to use.
Most electrical appliance manufacturers only require the size and riveting gap to be tested for riveted contact components. There is no clear requirement for riveting strength. Only a few manufacturers perform torsion testing on riveting strength. The torque detection method is as follows: use a saw blade to open a one-shaped groove on the rivet head of the riveted contact element, and then insert a torque wrench into the one-shaped open groove to rotate, and measure the torque value. Because most of the electrical contacts are made of copper-silver alloy, the strength is low, and it is easy to slip during the test, and when a saw blade is used to open the one-shaped groove, the width and depth cannot be accurately positioned, so the measured value fluctuates greatly. , has always been an unsolvable technical problem in the industry.
The inner hole retaining ring groove processing mechanism is characterized in that: it comprises a pneumatic grinder fixed block installed on the tool table of the lathe, a pneumatic grinder installed on the pneumatic grinder fixed block and a grinding wheel piece installed on the front end of the pneumatic grinder; The pneumatic grinder mounting block is provided with a pneumatic grinder installation through hole, and there are at least 2 screw holes above the pneumatic grinder installation through hole; the grinding wheel is designed according to the diameter of the product and the thickness of the groove width, in order to increase the strength of the grinding wheel , Add flanges at both ends of the grinding wheel to improve the strength of the grinding wheel. The grinding wheel piece includes the connecting blade on the flange plate. The center of the flange plate is provided with a mounting hole installed on the pen-type pneumatic grinder. The diameter of the mounting hole is 17.8- 18mm, the diameter of the grinding wheel is 18-20mm.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: boxed screw caps, Washers copper flat washers, metal rods with double ends supported by top pillars, finished cylindrical pins and other products, we can provide you with products such as Provide the right fastener solution for you.
