Service HotlineThe safety of screws and bolts in important occasions is related to the safety of the overall operation of the equipment, especially in public places and open air places, the theft of screws will cause major safety hazards. It is easy to loosen, and there is a safety hazard in long-term use.
The composition and proportion of this high-performance stainless steel screw thread are: 0.08%-0.15% C; 0.01%-0.60% Si; 0.02%-0.60% Mn; 0.01%-0.03% P; 0.002%- 0.03% S; 12%-14% Cr; 0.8%-1.5% Mo and the rest is Fe. The preparation method includes the following steps: smelting molten steel according to chemical composition requirements; hot rolling; annealing and pickling to obtain a stainless steel plate blank; coating and drying; cold drawing; cleaning and drying with a neutral activator; quenching; tempering ; coated and dried; drawn into stainless steel thread. This high-performance stainless steel screw line is energy-saving and environmentally friendly, with high corrosion resistance, high elasticity and high toughness. The preparation method and process are advanced and simple, and the production cost is low.
In the prior art, the electric screwdrivers in the automatic locking screw machines all adopt the suction method to absorb the screws. Such a structure is relatively complicated, and the design of the air circuit needs to be considered, and the phenomenon of material jamming is prone to occur, and it cannot be carried out due to the reason of the air circuit. Deep hole locking screws cause great trouble to users.
[In a preferred example of Guangdong Yueluo Hardware Industry Co., Ltd., the cone includes a large diameter end and a small diameter end, the diameter of the large diameter end is the same as the diameter of the inner hole in the middle of the nail body, and the diameter of the small diameter end is Two-thirds of the diameter of the large diameter end.
Stud bolts are manufactured in accordance with GB897-GB901 standards, the materials used are: Q235, 45#, 40Cr, 35CrMoA, Q345D, the specifications are: M3mm-M100mm, and the length can be customized according to user needs. High strength stud bolts, materials are 35#, 45#, 35CrMoA, 25Cr2MoV, 304, 316, 304L, 316L, 2H, 2HM, B7, B7M, B16, B8, 8, B8M, 8M, widely used in electric power, chemical industry , oil refining, valves, railways, bridges, steel structures, automobile and motorcycle accessories and other fields: generally used in mining machinery, bridges, automobiles, motorcycles, boiler steel structures, pendant towers, long-span steel structures and large buildings, etc. . Representation method of stud bolts: General stud bolts are expressed as: M12×100 GB 901-88 (standard) 35#/35# (material) 8.8 grade/8 grade (modulation grade) means: diameter = 12mm length = 100mm GB 901-88 adopts the national standard (of course, the industry standard can also be used as needed) stud bolt standard: GB 900-1988 Introduction to stud bolts Stud bolts save time and cost All stud bolt structures do not require drilling, Steps such as punching, threading, riveting, threading and finishing continue to expand the application potential of structural design, high current and small penetration. Therefore, welding to very thin sheets is possible. The workpiece for stud welding must be welded from one side. Can be soldered in all positions, with the help of extenders on vertical bulkheads that can be restricted. Since it is welded for a short time and there is little deformation after welding, no trimming is required. Because the welded structure does not require drilling, there is no leakage. The joint can achieve high strength, that is, the joint strength of stud welding is greater than the strength of the stud itself. How to install studs Good economy The advantage of other welding methods is the welding power. For mass-produced workpieces, standard studs are low cost. There are various types of equipment and welding torches, and the acquisition cost of equipment is relatively low. According to the product, it can be made into a multi-station automatic welding machine, or a high-precision gantry-type CNC automatic welding machine. Stud welding has high quality reproducibility and low rejection rate. However, in the application of stud welding, it should be noted that, like other fusion welding, there are certain restrictions on the carbon content in the steel. For structural steel studs, welding should be performed according to the recommended combination of stud material and base metal. There will be infusibility with the base metal. Combinations of stud material and base metal outside the recommended range shall be tested to determine the weldability and the product design requirements of the anchor bolt for the possibility of relevant inspection and evaluation.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: GB9074.17 screws, 1.5 teeth 12.9 grade bolts, welcome to sample processing, copper flat washers and other products, we can provide you with suitable fasteners Firmware Solutions.
