Service HotlineDuring the daily use and operation of mechanical equipment, due to the influence of external load, internal stress, wear, corrosion and natural erosion, individual parts or the whole change size, shape, mechanical properties, etc., which reduces the production capacity of the equipment. The consumption of raw materials and power increases, the quality of products decreases, and even personal and equipment accidents are caused. Therefore, in order to make the machinery and equipment can often play the production efficiency and prolong the service life of the equipment, the equipment must be properly repaired and routinely maintained.
screw is a tool that uses the physical and mathematical principles of the circular rotation and friction of an object to fasten the mechanism of the object step by step. When using screws to fasten objects and parts, it is often necessary to use screws with spring washers and flat washers to lock and fix the relative position, so as to improve the stability of the fastening connection and make the screws less prone to loosening. However, in the prior art, the method of manually inserting the spring washer and the flat washer in sequence is generally used, which not only increases the workload of the staff, but also makes the installation efficiency relatively low. On the other hand, the traditional screw with a gasket only has the function of fixing, Without the function of sealing, it cannot be applied to special equipment such as oil tanks and airtight cabins. Therefore, it is necessary to design a screw that can reduce the workload and have its own sealing structure.
With the popularization of electrical equipment, the door cover that integrates the panel, the controller, the sealing and waterproof function and the appearance decoration has gradually been required for equipment matching. The head directly affects the appearance, and for kitchen equipment such as dishwashers, the fixing screws of the door cover are easily rusted in direct contact with the washing water, which urgently needs a door cover structure that is easy to disassemble but does not affect the appearance.
① Nominal thread outer diameter (thread specification): divided into metric system and inch system. Metric thread → common specifications are 2; 2.3; 2.5; 2.6; 2.9; 3; 3.1; 3.5; 4; 4.2; 4.5; The unit is mm (millimeters). Inch thread→ Common specifications are 2#;4#;6#;8#;10#;12#;1/4;7/32;5/16;3/8;1/2 ;9/16;3/ 4. The unit is in (inches). ② Number of teeth/pitch: Definition of number of teeth → the number of teeth lines in one inch (25.4mm) length. Pitch Definition → Distance value between two adjacent threads. Conversion of number of teeth and pitch of teeth → pitch of teeth = 1 inch/number of teeth ③Nominal length: divided into metric system and inch system. Metric Nominal Length → Common values are 5, 6, 6.5, 7, 8, 9, 9.5, 10, 11, 12, 13, 14, 15, 16, 18, 19, 20, 21, 25, 28, 30, 31 , 32, 35, 40, 42, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100, 110, 120. The unit is mm (millimeters). Imperial Nominal Length → Common values are 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, 3/4, 1, 2, 3. Units: in (inches). ④Head type: use letters to indicate the type of head type, please refer to the previous classification of commonly used screw head types. ⑤Tooth type/tail type: Use letters to indicate the type of tooth type/tail type, please refer to the previous Commonly used screw thread/tail type classification. ⑥Groove type: Please refer to the previous section Category of common screw groove types of our company. Cross-slotted or non-slotted (such as punched hexagon head screws) do not need to be marked here, and other groove types need to be described in words. ⑦Special labeling: In general, no labeling is required. When expressing its characteristics, it is described in words at this position. For example: the specification name of the screw is described as 4-0.7x70PM±tooth length 35, which means 4 is the nominal diameter of the screw thread, 0.7 is the pitch, 70 is the nominal length of the screw, and P means its The head type is a pan head, M means its tooth type/tail type is a wire thread type, ± means its groove type is ± groove and can also be expressed by plus or minus groove. Tooth length 35 is special Mark, specify the thread length value of this screw.
The existing adjusting screw is generally composed of a screw and a nut on the top of the screw. The screw is driven to rotate by means of a screwdriver, and then the screw is driven to rotate. In and out, adjusting other objects connected to it and changing position accordingly.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: fine and coarse thread hexagon nuts, acrylic bolts, hexagon self-locking nuts, ABS isolation columns and other products, we can provide you with suitable fastening products piece solution.
