Service Hotlinerivet assembly device is provided with a base, the middle of the base is provided with a vertical groove, the bottom wall of the vertical groove extends forward and a horizontal convex block is suspended; the top surface of the convex block is fixed with a vertical rivet Needle and a guide column, the column body of the guide column is covered with a return spring; a downwardly open sliding block is mounted on the convex block, and the upper ends of the rivet needle and the guide column respectively protrude into the sliding block on the top wall of the sliding block. In the riveting pin hole and the guide hole, the inner wall of the riveting pin hole is provided with a large upper and a lower small horizontal step; the upper part of the bottom wall of the vertical groove is provided with a guiding limit rib. Guangdong Yueluo Hardware Industrial Co., Ltd. sets the rivet needle under the workpiece, and uses the upper die punch to press down the workpiece, and the rivet needle completes the operation of the rivet, omitting the operator to turn over and carry the rivet terminal board, thus effectively avoiding the rivet from The phenomenon that the rivet hole comes out. In addition, during operation, the workpiece is placed on the top surface of the slider, and the workpiece guide limit ribs and guide columns are used as shafts and radial limiters respectively. The riveting quality is good, and the purpose of saving time and labor and high efficiency is achieved.
The screw and nut disassembly and assembly tool of Yueluo also includes a rotating rod, a sleeve and a fixed rod fixedly connected to the sleeve rod at one end, and the other end of the fixed rod is connected with one end of the rotating rod to make the rotation The rod can be rotated around the connection point, and the sleeve for accommodating nuts or screws is fixedly connected with the other end of the rotating rod; rotating the rotating rod makes the sleeve head and the opening of the sleeve opposite , by keeping the nut or screw in the sleeve fixed while the corresponding screw or nut in the sleeve head rotates, so as to achieve simultaneous force and disassembly of the screw and the nut.
Make further details to make the technical scheme of Guangdong Yueluo Hardware Industry Co., Ltd. easier to understand and master. As shown in Figure 1, Yueluo is a schematic diagram of the thread design structure of the plastic screw of Guangdong Yueluo Hardware Industry Co., Ltd. It can be seen from the figure that this creation mainly controls the tooth angle of the thread. Compared with the normal tooth angle of many self-tapping screws, which are 48 degrees, 60 degrees and 34.5 degrees, the tooth angle of Guangdong Yueluo Hardware Industry Co., Ltd. The profile angle is formed by a 30-degree asymmetrical thread I. In particular, the asymmetrical thread I has a forward thread angle greater than the reverse thread angle. A more preferred embodiment is an asymmetric thread. The tooth profile angle α of the in-line installation is 20 degrees, and the tooth profile angle β of the reverse installation is 10 degrees. With this narrower non-stacked thread, the radial pressure on the plastic material is effectively reduced. In addition, the connecting bottom surface 11 between the screw teeth is designed as a circular arc surface. In the process of forming the self-tapping thread, it is more conducive to the flow of the material and the formation of the thread, and at the same time, the material can be more closely matched with the screw. Moreover, the radial pressure of the casing is relatively uniform, and the formed threads are not easily damaged. Yueluo has been tested by a series of professional parameters. Compared with other traditional screws, the plastic screws designed by Guangdong Yueluo Hardware Industry Co., Ltd. have better radial pressure, shell deformation after installation, load distribution, installation torque, drawing The force distribution, the strength of the pull-out force and the mounting torque range all show advantages. In particular, it can be installed with less torque to achieve the same clamping force and pulling force. Compared with a specific parameter, the thread strength of Delta-PT is 387N, while the thread strength of Guangdong Yueluo Hardware Industry Co., Ltd. reaches 444N. Yueluo can understand the plastic screw structure and implementation of Guangdong Yueluo Hardware Industry Co., Ltd. detailed above. It can be understood that through the improvement of the special thread structure, the radial pressure and installation torque during screw installation are reduced, and the damage to the plastic hole is reduced; And the pull-out resistance of the screw is increased, and it is not easy to appear loose in the assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
At present, with the development of my country's railway industry, many railway fastener systems involve T-bolts. The structure is shown in Figure 1. The dimensions that need to be inspected are head width A, head length B, and head straight table height. C. The height of the head slope D, the total length of the bolt E, and the major diameter of the bolt F. Due to the irregular shape of these places to be inspected, the measurement is difficult. The measurement of general measuring tools is not only slow, but also difficult to control human errors, resulting in some extreme upper limits and There are disputes and misjudgments about the size of the extreme lower limit when judging qualified and unqualified.
M4 grounding screw used to fix the grounding wire on household appliances and other equipment, the stud is cylindrical, and the thread is perpendicular to the end (section) surface. However, the screw holes on the equipment all have tapping guide grooves for sinking and guiding due to the manufacturing process requirements. When fixing the ground wire, if the screw is not positioned accurately (the screw is inclined), the screw is pressed down hard, which is easy to cause the screw and the screw. The screw hole bites the teeth, and after biting the teeth, it is easy to cause the screw to loosen or fall off, posing a safety hazard.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: jack screws, wide-sided flat washers, variable diameter screws, corner nails and other products, we can provide you with suitable products for you Fastener Solutions.
