Service Hotlinescrew is a tool that uses the physical and mathematical principles of the circular rotation and friction of an object to fasten the parts of the object step by step. Since the parts to be fixed are different, different types of screws are required for different applications. Press screw is a new type of fastener applied to thin plate or sheet metal. The principle is to press the embossed teeth into the preset holes of the sheet metal. The diameter of the general preset holes is slightly smaller than the outer diameter of the pressure riveting screw. The periphery of the hole is plastically deformed, and the deformed object is squeezed into the guide groove, thereby producing a locking effect. However, the existing pressing screws are easy to loosen due to long use time or frequent vibrations, which is prone to certain hidden dangers.
screw assembly includes a screw body, a spring and a mounting plate, the screw body includes a nut and a screw, the top of the screw is provided with a polygonal notch, the screw is composed of upper and lower parts, and the diameter of the upper part of the screw is larger than that of the lower part of the screw A slot is arranged at the lower end of the upper part of the screw rod; a slot corresponding to the spring is arranged on the mounting plate, and an extension slot is arranged in the slot, and the extension slot is L-shaped; an extension body is arranged at one end of the spring , the extension body corresponds to the extension slot; the spring is installed between the nut and the mounting plate, and the spring extension body is installed in the slot extension slot. Guangdong Yueluo Hardware Industry Co., Ltd. has the following advantages: it can prevent the spring from rotating with the rotation of the screw, the structure is simple, and the use is convenient.
In order to achieve this technical purpose, the plan of Guangdong Yueluo Hardware Industry Co., Ltd. is: a new type of open rivet, including a rivet body and a mandrel, the rivet body and one end of the mandrel are fixedly connected, and the lower end of the rivet body is provided with There is a round table, the top of the mandrel is provided with a nail head pit, the mandrel is provided with a stop groove, the lower side of the stop groove is provided with a mandrel breakpoint, and the mandrel is set on the mandrel. There is a stop ring, the stop ring is located on the lower side of the round table, and the lower side of the stop ring is provided with an assembly warp.
The inner hole retaining ring groove processing mechanism is characterized in that: it comprises a pneumatic grinder fixed block installed on the tool table of the lathe, a pneumatic grinder installed on the pneumatic grinder fixed block and a grinding wheel piece installed on the front end of the pneumatic grinder; The pneumatic grinder mounting block is provided with a pneumatic grinder installation through hole, and there are at least 2 screw holes above the pneumatic grinder installation through hole; the grinding wheel is designed according to the diameter of the product and the thickness of the groove width, in order to increase the strength of the grinding wheel , Add flanges at both ends of the grinding wheel to improve the strength of the grinding wheel. The grinding wheel piece includes the connecting blade on the flange plate. The center of the flange plate is provided with a mounting hole installed on the pen-type pneumatic grinder. The diameter of the mounting hole is 17.8- 18mm, the diameter of the grinding wheel is 18-20mm.
The product structure in the known technology includes a T-shaped bolt with a longitudinal section, and a polygonal nut matched with the bolt. The bolt is divided into two parts: the screw and the screw head. The screw head is placed at one end of the screw to form an integral part. The radial length of the tightening surface of the screw head is greater than the radial length of the screw, and its axial length is less than the axial length of the screw; The solid surface is a polygon, and now a hexagon is commonly used. The periphery of the base of the nut and the screw head has a number of elastic surfaces corresponding to the polygon; the periphery of the axial screw is provided with an external thread matching the internal thread of the nut. In actual use, the fastener of this structure can be tightened by using a conventional screw, such as a wrench. Therefore, its anti-theft performance is poor and it is not suitable for occasions with special requirements.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: large flat head screws, color zinc bolts, copper-plated fasteners, O-type closed joint bolts and other products, we can provide you with suitable products for you. Fastener Solutions.
