Service HotlineMost of the existing belts control the length of the belt by fixing the other end of the belt by the buckle, and the period that is often buckled by the buckle will be deformed and damaged after long-term use, and the user may change the position from standing to sitting or after meals. The circumference of the belt can be adjusted, and micro-adjustment is not necessarily possible when adjusting the tightness of the pin buckle type or buckle plate type belt buckle. In order to solve this problem, it is necessary to design a belt that is relatively suitable for the waist of a person.
At present, there are two methods for removing rivets in the market, one is non-destructive manual removal, which has low work efficiency and high work intensity. The other is mechanical destructive dismantling, such as the electric drill dismantling method. This method has high work efficiency, but it is easy to cause damage to the riveted product, and it is easy to cause the rivet to splash, and the operation is dangerous.
The cylindrical pin is mainly used for positioning and can also be used for connection. It is fixed in the pin hole by means of interference fit. Cylindrical pins used for positioning are usually not subject to load or a small load, the number is not less than two, distributed in the symmetrical direction of the overall structure of the connected parts, the farther the better, the pin is in each connected part The length is about 1-2 times the minor diameter. Cylindrical pins can also be used as shafts, and a straight shaft can also be used as cylindrical pins or even centering pins. So what's the difference between a shaft and a pin? The shaft can be used to transmit torque, bear bending moment and torque, and the cylindrical pin can be used for positioning, bear extrusion force and shear force. In a sense (such as small equipment), cylindrical pins can also be used as shafts.
1. First remove the sludge on the surface of the broken head of the broken screw, use the center gun to kill the center gun of the section, and then use an electric drill to install a drill bit with a diameter of 6-8 mm to drill the hole in the center of the section, pay attention to the hole must be drilled through. After the hole is drilled through, remove the small drill bit and replace it with a drill bit with a diameter of 16 mm, and continue to expand and drill through the hole of the broken bolt. 2. Take a welding rod with a diameter of less than 3.2 mm and use a medium and small current to carry out surfacing welding from the inside to the outside in the hole of the broken bolt. Take half of the entire length of the broken bolt at the beginning of the surfacing welding. When starting the surfacing welding, the arc should not be too long. In order to avoid burning through the outer wall of the broken bolt, surfacing to the upper end face of the broken bolt, and then continue surfacing to weld a cylinder with a diameter of 14-16 mm and a height of 8-10 mm. 3. After the surfacing is completed, hammer the end face with a hammer to make the broken bolt vibrate along its axial direction. Due to the heat generated by the previous arc and the subsequent cooling plus the vibration at this time, the broken bolt and the thread of the body will be loose in between. 4. Carefully observe, when it is found that a small amount of rust leaks from the fracture after the knock, take the M18 nut and put it on the surfacing column head and weld the two together. 5. After welding, use a torx wrench to cover the nut while it is still hot, and twist it back and forth, or tap the end face of the nut with a small hand hammer while twisting back and forth, so that the broken bolt can be taken out. 6. After taking out the broken bolt, use a suitable tap to process the thread in the frame to remove rust and other debris in the hole.
In mechanical devices, there are many ways to install and connect two components, such as bolt connection, welding, etc., but for installation and connection in a narrow space, such as the socket of two hollow cylinders with smaller diameters, due to the relatively small space It is very difficult to use this method, and it is extremely inconvenient to install and connect.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: percussion flat cap GB109 rivet iron natural color GB867 round head rivets, high head knurled nuts, iron natural color hexagonal nuts, structural blind rivets, etc. products, we can provide you with the right fastener solution for you.
