Service HotlineA pull rivet, this kind of pull rivet has good installation performance, firm connection and long service life, but the defects are: first, after installation and use, if it is damaged, it cannot be reused; second, it is convenient to disassemble, and it also increases the possibility of theft ,. It is not conducive to safety; 3. There is still the possibility of movement in the circumferential direction of the collar, which will affect the riveting effect.
An elastic cylindrical pin assembling device, the assembling device includes an adapter handle, a punching needle, an elastic piece, a fixed sleeve and a telescopic sleeve, the adapter handle and the fixed sleeve are fixedly connected, and the punching needle is inserted into the adapter handle and fixed Inside the sleeve and its upper end is pressed against the adapter handle, the lower end of the punch needle is also inserted into the fixed sleeve and moves relative to the fixed sleeve in the up and down direction when the adapter handle pushes it to move up and down, the fixed sleeve A reset spring is also set between the punch and the punch, the lower end of the fixing sleeve has an insertion hole for the elastic cylinder pin, that is, a working cavity, and the lower end of the punch needle is also provided with a push fit for the upper end of the elastic cylinder pin. the positioning boss. When the elastic cylindrical pin assembling device is used, after assembling an elastic cylindrical pin, the elastic cylindrical pin needs to be re-installed into the fixed sleeve, which cannot realize continuous assembly and has low assembly efficiency.
Below in conjunction with the accompanying drawings, Guangdong Yueluo Hardware Industry Co., Ltd. is described in further detail. Please refer to FIG. 2 and FIG. 3, a locking nut includes a nut 1, the bottom is circular, the middle is hexagonal, the top is circular, there is a bolt hole in the center, and the side wall of the bolt hole is threaded. A number of flattening notches 2 are arranged on the top of the nut. According to the locking nut of the preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the number of the flattening notches 2 is three. Due to the above features, the three flattening gaps can be used as the focal point of the tightening tool and the clamping place of the anti-loose gasket bayonet, and the structure is simple and can be formed by die stamping at one time. The above disclosure is only a preferred embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., and does not limit itself. Any person skilled in the art, without violating the spirit of the present invention, can think of changes that fall within the scope of It is within the protection scope of Guangdong Yueluo Hardware Industry Co., Ltd.
Some heavy equipment such as large motors, large reducers, etc., in order to facilitate the installation and adjustment of equipment and the need for maintenance space, a certain position needs to be moved during equipment installation and maintenance. Usually, a steel base or platform is set under the equipment, and the base or The platform is provided with an oblong bolt installation slot, commonly known as an oblong slot, as shown in Figure 1--Figure 4. When using common hexagon head bolts or common T-bolts with the long circular groove in Figures 1 and 2, auxiliary fixing bolts or welding stoppers are required on the back of the long circular groove to prevent the bolt from rotating when the nut is tightened. In Fig. 3 and Fig. 4, the long circular groove itself has a clamping groove to prevent the rotation of the bolt, but this structure greatly increases the processing cost of the long circular groove.
Nuts cooperate with screws to achieve the fixing and connection of components. SMD nuts are generally used in the circuit board industry to fix electronic components. That is, the chip nut is soldered on the circuit board by solder, and the electronic components are fixed by turning the screw. However, when the current chip nut is soldered on the circuit board, there may be uneven soldering, which makes the soldering untidy. At the same time, during soldering, the excess solder overflows from the periphery of the nut, which affects the appearance and may affect its appearance. electrical properties. In addition, the nut is only welded with the circuit board on one end face, and its firmness and reliability after welding are low.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: manganese steel washers, non-standard washers, American standard K cap nuts, 304 countersunk head bolts and other products, we can provide you with suitable tightening screws for you. Firmware Solutions.
