Service HotlineRiveting nut tool is a special installation tool for riveting nut, including pneumatic riveting nut and electric riveting nut. Pneumatic riveting nut tool has the advantages of fast speed and large pulling force, but it is difficult to rotate into and unscrew the riveted nut. The rotating blade of the moving motor is frequently used or in a slightly dusty working environment, it will suddenly get stuck and not work, there is a great hidden danger of motor crash, and the torque of the air motor is small due to the limitation of the volume, although the riveting pulling force can be done to larger defects, but the volume also increases.
When checking the finished blind rivet, check: the diameter of the rivet body, the length of the rivet body, the thickness of the rivet body cap, the diameter of the cap, the total length of the mandrel, the exposed size of the mandrel, the size of the nail cap, and the outer diameter after assembly can be considered. In the actual inspection, the weak links of the product can be measured, such as: tensile force, shear resistance, and core pull-out resistance. The key is to pay attention to the rivets, if the rivets are insufficient, whether they are riveted in place; or because the cap of the mandrel is too large, so that the mouth of the rivet body cannot be pulled down; and there are jump heads, that is, the mandrel is too low or broken. The size is too small etc. Length measurement of closed blind rivets
In the prior art, the beams used for installing the curtain wall are mainly divided into two types: closed-cavity structure and open structure, and angle aluminum connection is mainly used for the connection between the beam and the column. As far as the beam of the closed-cavity structure is concerned, after the angle aluminum is used to connect, there are open bolts on both ends of the upper surface of the beam, and the aesthetic performance is extremely poor. As far as the beam of the open structure is concerned, in the actual connection, first fix one corner of the angle aluminum to the beam, and then connect the other corner of the angle aluminum to the column; due to the limited operating space in the beam of the open structure, the angle aluminum is not It is easy and accurate to install, and it takes a lot of time to install; and when the curtain wall panel is heavy, the beam will be twisted, causing the gusset of the opening part of the beam to fall. In addition, due to the limitation of the opening structure itself (an additional gusset or clasp), the aluminum content of the beam is relatively heavy, and the manufacturing cost is high.
In CN203807560, nails and bolts are used to connect the plates, but the heads of the nails and the bolts are enlarged ends that are wider than the rods, and the heads of the nails and the bolts cannot penetrate into the interior of the door body, so in terms of appearance, the more More nails and bolts will leave more spots on the surface of the door that are not suitable for the door itself. In the prior art, the treatment method for these spots is generally to paint with paint, which can only make the door panel consistent with the head of the nail and the bolt in color, but cannot change the shape of the head of the nail and the bolt, and the appearance is still good. Obvious spots were noticed, which made the door panels connected by nails and bolts to the panels, which could not be used as door panels for household doors.
Half round head rivets are mainly used for riveting occasions with large lateral loads, and are the most widely used. Flat cone head rivets are often used in riveting occasions with strong corrosion such as ship hulls, boiler water tanks, etc. Countersunk head and 1200 countersunk head rivets are mainly used for riveting occasions where the surface must be smooth and the load is not large. Half countersunk head and 1200 half countersunk head rivets are mainly used for riveting occasions where the surface must be smooth and the load is not large. Flat head rivets are used for riveting occasions with general load. Flat head and flat head rivets are mainly used for riveting of metal sheets or non-metallic materials such as leather, canvas and wood. Large flat head rivets are mainly used for riveting of non-metallic materials. Semi-hollow rivets are mainly used for riveting occasions with small loads. Headless rivets are mainly used for riveting of non-metallic materials. Hollow rivets are light in weight and weak in head, and are used for riveting of non-metallic materials with small loads. Tubular rivets are used for riveting of non-metallic materials without load. Nameplate rivets are mainly used for riveting nameplates on machines and equipment.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: national standard inch, butt-locking screws iron countersunk head rivets, inner cross recessed combination bolts, chassis isolation column copper stud nuts and other products, we can Provide you with the right fastener solution for you.
