Service HotlineThe main function of the spring washer is to prevent the nut from loosening. It is also known that: the existing spring washer is a ring made of spring steel, and then a gap is cut in the diameter direction on the ring, and the heads on both sides of the gap are cut. The material of the part is turned to two different sides of the ring to form a pawl, and the purpose of preventing loosening is achieved by the fit between the pawl and the nut on the surface and the workpiece. Obviously, only one pawl is used to achieve the purpose of preventing loosening. Since the braking force generated by one pawl is limited, there are defects of poor braking effect and poor anti-loosening effect.
The history of screws was broadcast in 1986. Our country formulated a new standard for standard parts, which is commonly known as the new standard in the business. The most used ones are GB5780, GB5781, GB5782, GB5783, GB5784. GB5780 is a hexagonal head thick shank half-thread screw, its accuracy grade is C-grade product, which can be replaced by GB5782 (GB5782 is a hexagonal head thick shank full-thread screw, and its accuracy grade is grade A and B.) GB5781 is a hexagonal head full-thread screw. Threaded screw, the accuracy grade is C grade product. It can be replaced by GB5783 (GB5783 is a hexagonal head full-tooth screw, and its accuracy grades are A and B). GB5784 is a hexagon screw with thin rod and half teeth.
In another embodiment of Guangdong Yueluo Hardware Industrial Co., Ltd., the conveying device 3 includes a motor 31 and a circular rotating disk 34, the motor 31 drives the circular rotating disk 34 to rotate, and the circular rotating disk 34 is evenly provided with screws in the circumferential direction. The matching screw accommodating hole 35, the screw enters the screw accommodating hole 35, the motor 31 drives the circular rotating plate 34 to rotate, so that the screw is first slotted by the cutting wheel 42, and then polished by the fixing wheel 48, and the screw is in the screw accommodating hole 35. It is fixed, which is more secure and reliable during the slotting process. Preferably, the circular rotating disk 34 includes a circular rotating disk 32 and a sector-shaped fixed disk 33. The circular rotating disk 32 is evenly provided with screw receiving recesses matching the screws in the circumferential direction, and the recesses and the sector-shaped fixed disk 33 are formed with the screws The matching screw receiving holes face the cutting wheel 42 and the fixing wheel 56 .
When using, after installing the nut and the bolt in place, insert the locking strip from the groove of the bolt, and make the V-shaped locking teeth of the locking strip snap into one of the V-shaped tooth grooves, and push the locking strip into the groove as a whole. The V-shaped locking teeth are stuck in the nut, and the locking strip body is stuck in the groove of the bolt, thereby restricting the relative rotation of the nut and the bolt, and there are threads between the nut and the bolt to restrict their relative sliding, so it can prevent the nut from loosening, even from The bolt falls off; when the nut needs to be disassembled, it is only necessary to pull out the locking strip from the groove, and the nut can be disassembled normally.
Ordinary T-bolts, the bolt head is rectangular, the screw part and the bolt head are T-shaped, and the width of the head is smaller than the width of the opening part of the T-slot, so that the head of the T-bolt can extend from the length of the T-slot. Insert the T-slot into the T-slot at any position in the direction. When the workpiece needs to be fixed, turn the T-bolt 90 degrees so that the length of the head is perpendicular to the T-slot, hook the inside of the opening of the T-slot, and screw it by tightening The nut on the T-bolt threaded rod holds the workpiece in place. The T-bolt of this structure can easily connect the bolt and the base piece quickly, and is widely used, but there are also some shortcomings, due to the contact area between the head of the T-bolt and the inner side of the opening of the T-slot. If it is too small, the frictional resistance is correspondingly small. On the one hand, the bolts are easy to follow the rotation during the process of tightening the nut. Unreliable.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: 1587 hexagonal cap nuts, small yellow croaker plastic screws, stainless steel rivet nuts, yuan nuts and other products, we can provide you with suitable fastener solutions for you Program.
