Service HotlineAt present, it has become very common to use automated tools to hit screws. However, when the material of the fastening object is relatively soft, the screw fastening is often prone to skew, not sticking, and the screw hole is damaged during the fastening process. Metal shavings can also be created in the shards, which can short out the board.
The national standard name of the cross recessed small pan head three-combination screw is the cross recessed small pan head screw, the spring washer and the flat washer assembly. The national label is GB/T9074.8-1988. This 1988 refers to the year, that is, this standard is the standard issued by the country in 1988. The specifications of the cross recessed small pan head three-combination screw, our company's minimum is M2.5, the shortest is 5mm, the largest is M10, and the longest is 90mm. Of course, as customers have higher and higher requirements for small pan head combination screws, or require smaller and longer combination screws. If the quantity is large, or with the development of our company. Buy some advanced combination screw machines. Come and go to meet the higher requirements of our customers.
When the nut is tightened on the stud, there will inevitably be an empty upstroke. That is, when the nut has not reached the part that needs to be tightened, the nut needs to be twisted on the non-locking (working) part of the front end of the stud by hand or tool, so that the nut runs along the axial direction of the stud and reaches the part to be locked. . When the idling stroke of the thread at the front end of the stud is long or the thread pitch is small, the idling stroke before locking will waste a lot of time, resulting in a huge occupation of personnel or tools.
Traditionally used for plastic fastening screws, most of the thread designs are self-tapping threads, but for different plastic types, the self-tapping threads also have many different classifications, such as PT profile, Plastite series, Remform profile, etc. The structural parameters and manufacturing process of these threads are inconsistent, or require different main molds and wires. Therefore, to find a plastic screw that is universally applicable to various plastic types, has a single pressing structure, low-cost and simple manufacturing process, especially its special self-tapping thread, is an important issue that needs to be solved urgently at present. question. The purpose of Yueluo Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to propose a plastic screw to solve the screw fastening problem that is generally applicable to different plastics. The purpose of Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. is to realize a kind of plastic screw through the following technical scheme, it is characterized in that, the thread of the screw is composed of asymmetric threads with a profile angle of 30°, and the threads are The bottom surface of the connection between them is an arc surface. Yueluo preferably, the asymmetrical thread has a forward thread angle greater than the reverse thread angle, and the sum of the two-direction thread angles is 30°. Yueluo further preferred that the tooth profile angle of the asymmetrical screw thread in the forward mounting direction is 20 degrees, and the tooth profile angle in the reverse mounting direction is 14 degrees. Yueluo Guangdong Yueluo Hardware Industry Co., Ltd.'s application of plastic screws, through the improvement of special thread structure, reduces the radial pressure and installation torque when the screw is installed, reduces the damage to the plastic hole; and increases the pull-out resistance of the screw force, it is not easy to appear loose assembly. At the same time, the design of the bottom surface of the connection between the threads of the arc optimizes the flow of the material of the installation object, which improves the integrity of the installation connection.
The existing method of tightening large screws is generally 1. After the nut is screwed to the connected piece by hammering + nut angle method, use a casing to connect the lever arm of the wrench, or use a free hammer to hammer the plate handle, Rotate the nut an additional angle to obtain the required preload. This is not only a primitive and labor-intensive fastening method, but also has great limitations, such as limited space, or the screw itself is a rotating shaft and so on, it is difficult to use this method.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat head screws and bolts, ring nuts, SOO pressure riveting parts, nylon caps and other products, we can provide you with suitable fastening products piece solution.
