Service HotlineThe purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a flat gasket that improves the lubrication performance of the contact surface and reduces the friction of the contact surface. Yueluo is implemented through the following technical solutions: a flat gasket with straight upper and lower end faces, characterized in that: the upper and lower end faces are dotted with pits, the pits are spherical pits, and the pit diameter is 2-3mm , the pit depth is between 0.5-lmm. The bottoms of some of the pits are provided with through holes penetrating the upper and lower end faces, and the diameter of the through holes is not greater than 0.5mm. The flat gaskets provided by Yueluo have pits with reasonable design parameters on the upper and lower end faces of the flat gaskets. The pits can store oil, so the lubrication of the contact surfaces of the gaskets can be well improved. It can effectively reduce the friction of the contact surface of the gasket and reduce the failure rate; in addition, the design of the through hole enables a smooth oil passage between the upper and lower end faces of the gasket, ensuring that the upper and lower end faces can be well lubricated.
In the prior art, there are two ways to feed the screws of the locking screw machine, the air blowing type and the air suction type. The air suction type is suitable for relatively small screws. If the screw size is larger than M2, smaller than M5, and the length-diameter ratio is larger than 1.4, the air-blown screw machine can be selected.
Sprinkle the excess standard spring washer 7 on the positioning plate 12-1 on the spring washer positioning plate 2, and shake the spring washer positioning plate 2 by hand. After a short time, the spring washer 7 will be positioned and arranged on the upper positioning plate 12-1. In the upper spring washer hole 2-7, since the width of the opening groove 12-32 of the baffle plate 12-3 is smaller than the diameter of the spring washer hole 2-7, and the thickness of the upper positioning plate 12-1 is designed according to the thickness of the spring washer 7, Only one spring washer 7 can be accommodated in the spring washer hole 2-7 of each upper positioning plate 12-1, and the excess spring washer 7 is cleaned with a brush.
In chemical production equipment, the cylinder body and the head cover need to be connected and sealed. The traditional sealing structure is to connect the two with a screw, add a non-metallic gasket in the middle and fix it with a nut. However, such a sealing structure only controls the tightening torque, and has the technical defect that the sealing ring will be twisted or even broken during repeated loading and unloading of the cylinder head cover, resulting in poor sealing performance.
The conventional auger bit structure 1 includes a rod body 11, a screw head 12 provided on one end of the rod body 11, a drill tail 13 provided on the other end of the rod body 11, and a plurality of threads 14 arranged around the rod body 11; Wherein, the periphery of the drill tail 13 defines a parting line 15, and the parting line 15 makes the drill tail 13 symmetrically divided into a side 131 and a side 132, and a cutting end 133 is formed at the junction of the end of the side 131 and the end of the side 132, respectively. The cutting end 133 is concavely provided with a quarter-turn chip flute 134 in the same direction of the helix, and the edge 132 continues the chip flute 134 and has a quarter-turn chip flute 135 with different helical curvatures. , using the chip groove 134 and the chip groove 135 to be connected by different helical curvatures, so that the drill tail 13 can form a symmetrical and complete chip groove of 190 degrees.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: stainless steel internal expansion screws, carbon steel hexagon nuts, T-shaped nuts, circular decorative hollow washers and other products, we can provide you with suitable products for you fastener solutions.
