Service HotlineA T-bolt. This kind of bolt includes a bolt shank and a bolt head, and the bolt head adopts a special cylindrical bolt head, which can be suitable for installation and cooperation of various sizes. Although the shape of such a bolt head is greatly improved compared to the square bolt head in the prior art, the cylindrical bolt head is particularly inconvenient to install, and special installation tools must be used for installation. If the manual direct installation method is adopted, since the force area of the finger touching the side of the cylinder is small, it will increase the difficulty of the installation work and needs to be improved.
screw is a tool that uses the physical and mathematical principles of the circular rotation and friction of an object to fasten the parts of the object step by step. Since the parts to be fixed are different, different types of screws are required for different applications. Press screw is a new type of fastener applied to thin plate or sheet metal. The principle is to press the embossed teeth into the preset holes of the sheet metal. The diameter of the general preset holes is slightly smaller than the outer diameter of the pressure riveting screw. The periphery of the hole is plastically deformed, and the deformed object is squeezed into the guide groove, thereby producing a locking effect. However, the existing pressing screws are easy to loosen due to long use time or frequent vibrations, which is prone to certain hidden dangers.
Cabinets are one of the must-have furniture in home improvement homes. They are extremely useful. Various cabinets may be used in kitchens, bathrooms, bedrooms, living rooms, and even balconies. The traditional cabinets are assembled in advance and then placed in the appropriate position, which is very inconvenient to transport. Currently, the commonly used cabinets are spliced together with plates and hardware accessories. During production and transportation, the plates and hardware accessories are independent. For production, processing and transportation, after it is sent to the destination, it is assembled with the plates by screws and other hardware accessories to form the entire cabinet structure. The current cabinet installation structure usually exposes some hardware accessories such as screws on the outside or inside of the cabinet, which not only affects the overall aesthetics, but also scratches the items during use, which affects the use effect. Some designs allow a plastic fastener to be fastened on the outside of hardware accessories (mainly screws). Although it can alleviate the above problems to a certain extent, it still does not fundamentally solve the problem, and the integrity is still not good.
Comparing the physical properties of stainless steel and carbon steel, the density of carbon steel is slightly higher than that of ferritic and martensitic stainless steel, but slightly lower than that of austenitic stainless steel; the resistivity is based on carbon steel, ferritic, martensitic and The order of austenitic stainless steel is increasing; the order of linear expansion coefficient is similar, austenitic stainless steel is the highest and carbon steel is the smallest; carbon steel, ferritic and martensitic stainless steel are magnetic, austenitic stainless steel is non-magnetic, But its cold work hardening will generate magnetism when it is transformed into intensite, and heat treatment method can be used to eliminate this martensitic structure and restore its non-magnetic properties. Compared with carbon steel, austenitic stainless steel has the following characteristics: 1) High electronegative rate, which is about 5 times that of carbon steel. 2) The large coefficient of linear expansion is 40% larger than that of carbon steel, and with the increase of temperature, the value of the coefficient of linear expansion of stainless steel screws increases accordingly. 3) Low thermal conductivity, about 1/3 of carbon steel.
The production of non-standard round flat pads can only be processed on ordinary lathes without punching machines. Processing with round steel is difficult, material waste is large, tool loss is large, and efficiency is low. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to provide a non-standard circular flat pad lathe processing fixture, which is suitable for the production of various non-standard circular flat pads. Yueluo is realized in this way. It includes a hollow square support, a bolt and a circular machining groove. It is characterized in that a circular machining groove is left on one surface of the hollow square support. There are 4 bolts evenly connected. The advantages of Yueluo are: 1. Reduce the difficulty of processing; 2. Save materials (can use corner waste); 3. Reduce tool wear; 4. Improve production efficiency.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: black carbon steel bolts, copper hexagon head screws, countersunk head anti-theft screws and bolts, and other products made by professional manufacturers in Dongguan. We can provide you with suitable products for you. Fastener Solutions.
